← A5 Audi A5 repair manuals →

Audi A5 F5 (2021): Replacing the Front Left Exterior Door Handle

The exterior handle is attached to the door latch by a locking screw on the door's edge, hidden under a plug. The handle itself comes off outward after this screw is loosened, without removing the door panel. This guide covers the front left (driver's) door; on cars with Keyless, the handle contains a touch sensor with a connector. The torque values below are approximate, so check the exact figures against the manufacturer's specifications.

DifficultyMedium Time1-1.5 hours Steps26

Key figures

  • Locking screw tightening torquelight tightening, the screw holds the handle and is easy to strip; used in step 21
    about 2.5 N·m (1.8 lb-ft) (approximate)
  • Torx screwdriver sizefits the screw under the plug on the door edge (step 6); check the exact type against your screw
    T20

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: what holds the handle and how to remove it

Driver's door, outside glass ← to the hinges (front of the car) door edge → 1 2 remove: back and out open the door Door edge (door open) rubber seal lock 3 T20 screw: loosen a little, not all the way 4 Tap to enlarge
  1. 1door handle: comes off from the outside, the door card stays on
  2. 2lock cylinder cap at the end of the handle: it comes out after the screw is loosened and the handle is held open
  3. 3plug on the door edge, level with the handle: under it is the Torx T20 screw that holds the handle. Loosen it a little only: if it comes all the way out it falls inside the door
  4. 4rubber seal along the door edge: fold it aside to reach the plug

Parts

3
№PartAlternatives
01 Exterior front left door handle, body-color painted (with or without Keyless)1 pcFind on Amazon → AlternativesHellaFebiVan Wezel
02 Lock cylinder cap (handle end cover)Find on Amazon → AlternativesHellaFebiVan Wezel
03 Handle sealing pads (gaskets)if wornFind on Amazon → AlternativesHellaFebiVan Wezel

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

26 steps · 5 stages
Stage 1 of 5 Preparation 4 steps
  1. Determine your trim level: check whether the handle has a Keyless sensor (a sensor pad and a wire with a connector are visible on the handle) and whether there is a key lock cylinder. This determines whether you will need to disconnect a connector.
  2. On cars with Keyless, disconnect the negative battery terminal and wait a few minutes to prevent false triggering of the lock and the access system.
  3. Open the driver's door, close the window, and tape over the door edge and the fender next to the handle to avoid scratching the paint.
  4. On the door edge, next to the latch, find the rubber seal and the plastic plug (the opening for the locking screw).
Stage 2 of 5 Removal 9 steps
  1. Move the door's outer seal aside and carefully remove the plug over the opening by prying it out with a thin screwdriver.
  2. Through the opening, find the locking (clamping) screw and unscrew it with a Torx T20 screwdriver only partially, just until the handle comes loose. Do not unscrew it completely and do not press hard: the screw can fall inside the door, and then you will have to remove the door panel.
  3. Pull the exterior handle toward you and hold it in the "open" position.
  4. If a decorative lock cylinder cover or a handle end cap is installed on the edge, remove it: carefully release the retainers without breaking the clips.
  5. Push the lock cylinder retainer (spring latch) inward, toward the handle. The handle is now locked in the "open" position.
  6. Remove the lock cylinder (or the dummy cap housing on the passenger side) from the bracket by sliding it sideways. If it won't come out, insert the key, turn it slightly, and pull out the cylinder together with the key.
  7. Pull the handle itself toward the rear of the door to disconnect it from the actuating lever in the bracket.
  8. Tilt the handle outward and remove it from its seat in the bracket.
  9. On cars with Keyless, disconnect the touch sensor connector from the handle (press the connector lock and pull).
Stage 3 of 5 Transferring parts and preparing for installation 3 steps
  1. If needed, transfer the touch sensor (Keyless) or the cap to the new handle: the sensor comes out with light pressure from a screwdriver, and the cap by pressing in the two clips. The new cap snaps in with a click.
  2. Inspect the pads (sealing gaskets) under the handle. If they are torn, hardened, or have lost their shape, replace them, otherwise water will leak in and the handle will squeak.
  3. Clean the seat area of dirt and make sure the actuating lever in the bracket moves freely.
Stage 4 of 5 Installation 6 steps
  1. On a Keyless car, connect the connector to the new handle until it clicks.
  2. Insert the handle into the seat of the bracket so that it engages the hook.
  3. Rotate the handle back the other way by pushing its driver (pusher tab) against the actuating lever in the bracket.
  4. Push the lock cylinder retainer toward the handle and insert the cylinder (with its cap) into the bracket until it clicks.
  5. Tighten the locking screw on the door edge through the opening: torque approximately 2-3 N·m (1.5-2.2 lb-ft) — snug it lightly, without force, so you don't strip the plastic seat.
  6. Install the plug on the door edge and put the seal back in place.
Stage 5 of 5 Checking 4 steps
  1. Reconnect the negative battery terminal (if you disconnected it). Check the clock, power windows, and seat memory, and restore the settings if necessary.
  2. Open the door by the handle several times, close it, and check the operation of the central locking with the key fob button and with the handle from the inside.
  3. On a Keyless car, check that the door opens by touching the handle with the key in your pocket, and that it locks by touching the sensor pad.
  4. Check the fit of the handle: no play or misalignment, free travel, even gap. Remove the tape.

Common mistakes and warnings

  • The locking screw on the door edge is easy to unscrew too far — it falls inside the door, and you can only retrieve it after removing the door panel
  • Do not unscrew it more than needed to release the handle
  • For a Keyless handle, do not apply heavy force to the sensor, so you don't damage it
Spotted a mistake? Tell us →

Our articles

More articles →