Autopapyrus · BMW 3 Series 2.0d N47 (2009)
https://autopapyrus.com/catalog/bmw/3-series/guides/intake-repair-air-leaks-boost-pipes-and-intake-manifold-gaskets/
https://autopapyrus.com/catalog/bmw/3-series/guides/intake-repair-air-leaks-boost-pipes-and-intake-manifold-gaskets/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
BMW 3 Series 2.0d N47 (2009): Intake Repair, Air Leaks, Boost Pipes and Intake Manifold Gaskets
An air leak on the N47 shows up as loss of power, smoke, boost pressure fault codes and unstable idle. The most common culprits are cracked boost and intercooler pipes, hose connections, swirl flap blanking plug seals and intake manifold gaskets. First locate the leak, then replace only the faulty components.
Parts
7| № | Part | Genuine part no. | Alternatives |
|---|---|---|---|
| 01 | N47 intake manifold gasket set (one per cylinder)Find on Amazon → | 11617801943 | AlternativesElringVictor Reinz |
| 11618511917 | |||
| 11618508626 | |||
| 02 | Boost pipe, turbo to intercoolerif crackedFind on Amazon → | 11618513288 | |
| 11618506359 | |||
| 11618513289 | |||
| 03 | Boost pipe, intercooler to throttle bodyif crackedFind on Amazon → | 11618506359 | |
| 11614744639 | |||
| 11618519492 | |||
| 04 | Boost pipe O-ringsFind on Amazon → | 13717794556 | |
| 13717787197 | |||
| 05 | Boost pipe clampsFind on Amazon → | ||
| 06 | Intake manifold swirl flap blanking plug sealsif leakingFind on Amazon → | 11618512681 | |
| 11618511917 | |||
| 11617801943 | |||
| 07 | Intake manifold mounting boltsif single-useFind on Amazon → | 07129907128 | |
| 11617812939 | |||
| 11618511918 |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
8- Socket and wrench set Amazon →
- Torx set (external and internal) Amazon →
- torque wrench 5-25 N·m (4-18 lb-ft) Amazon →
- pliers for hose clamps Amazon →
- smoke machine or hand pump with pressure gauge for intake leak testing Amazon →
- can of carburetor cleaner or foam sealant Amazon →
- clean rags Amazon →
- plugs to seal open ports Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 27 more.
See manuals →
Step by step
11 steps- Read the engine fault codes and check the actual boost pressure. If it is lower than specified under load, suspect a leak downstream of the turbo. Remove the engine cover.
- Inspect the air path: the turbo-to-intercooler pipe, the intercooler, and the intercooler-to-throttle pipe. Look for oil seepage, cracked rubber and loose clamps. An oily film at a joint indicates a leak.
- Pressure test the intake at about 0.3-0.5 bar (4-7 psi) using a smoke machine or a hand pump with a gauge, with the inlet before the turbo plugged. The leak will show as smoke or can be heard. Do not exceed the specified pressure, to avoid damaging sensors and flaps.
- If the leak is in the pipes, remove them. Disconnect the sensor connectors on the pipes, loosen the clamps or release the quick-release retainers. Replace the pipes and O-rings, and tighten the clamps moderately and evenly, without skewing (usually 3-5 N·m (27-44 lb-in)). Clean the mating surfaces of oil before installing.
- If the leak is in the manifold area: disconnect the negative battery terminal. Remove the air duct to the throttle body, the pipe and, if necessary, the air filter and its housing. Disconnect the connectors of the boost pressure and temperature sensor, the throttle valve, the swirl flap actuator, and the vacuum and vent hoses.
- Remove the exhaust gas recirculation (EGR) pipe and valve with the cooler if they block access. Cover the open ports with a clean cloth or plugs so that dirt and debris do not get into the cylinders.
- Remove the intake manifold mounting bolts and carefully lift off the manifold. Do not drop any bolt or piece of gasket into the ports. Note the positions of bolts of different lengths.
- Inspect the manifold: carbon and oil deposits inside are normal for a diesel and can be removed with cleaner. Check that the swirl flaps move freely and that the blanking plugs seal properly. If the flaps stick or the linkages break, replace the manifold as an assembly.
- Clean the mating surfaces of the cylinder head and the manifold without scratching them. Install new gaskets (one per cylinder) in the correct position. Do not lubricate the seals unless the manufacturer specifies it.
- Install the manifold and tighten the fasteners in two or three stages from the center outward. The torque for N47 manifold bolts is usually about 10-22 N·m (7-16 lb-ft); the exact value depends on the bolt and should be confirmed in the manufacturer's specifications. Install the pipes and connectors in reverse order.
- Reconnect the battery, start the engine and check how it runs at idle. Repeat the pressure test or inspect the joints for smoke and oil seepage. Clear the fault codes and take a test drive under load, checking the boost pressure.
Common mistakes and warnings
- Work on a cold engine and do not let any foreign objects get into the intake: even a small fragment entering a cylinder can lead to serious engine repairs
- On the N47, damage to or wear of the swirl flap actuator can cause the flaps to fall into the intake, so if there is play and a characteristic noise from the manifold in operation, assess its condition in advance
- If you have no experience disassembling engines, leave the job to a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of BMW
BMW AG stands for Bayerische Motoren Werke, or "Bavarian Motor Works." BMW is a major manufacturer of cars, engines…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →