https://autopapyrus.com/catalog/byd/f3/guides/engine-management-system-diagnostics/
BYD F3 1.5 (2007): Engine Management System Diagnostics
The 1.5 BYD F3 engine is controlled by an electronic control unit (ECU) based on sensor signals. When a sensor or its circuit fails, the ECU turns on the Check Engine light and stores a code. The diagnostic approach is: read the codes, check the simple causes (hoses, connectors, contacts), then test the specific sensor or circuit instead of replacing parts at random. Tightening torques and sensor electrical values are not listed below. Check them against the manufacturer's service manual.
Diagram: where the ignition coil is and what connects to it
- 1Ignition coil: a black box with a yellow sticker. With misfires and jerking it is removed and checked; replace with the same type or a set for all four cylinders.
- 2Coil connector with latch: check for oxidation and poor locking, clean the contacts with electrical contact cleaner.
- 3Coil mounting bolt on the metal bracket: undo it to remove the coil and reach the spark plug.
- 4Rubber boot on the coil stem: it sits on the spark plug in the well. Under it, judge the plug by carbon, oil and electrode wear.
- 5Wiring harness from the connector: check for chafing, oil and moisture, and broken wires.
- 6Fuel rail with hose runs over the coil: a landmark. Check the fuel system with a pressure gauge away from open flame.
Parts
8| № | Part |
|---|---|
| 01 | Manifold absolute pressure (MAP) sensorif faultyFind on Amazon → |
| 02 | Crankshaft position sensorif faultyFind on Amazon → |
| 03 | Throttle position sensorif faultyFind on Amazon → |
| 04 | Idle air control valveif faultyFind on Amazon → |
| 05 | Ignition coilsif faultyFind on Amazon → |
| 06 | Spark plugsif faultyFind on Amazon → |
| 07 | Oxygen sensorsif faultyFind on Amazon → |
| 08 | Intake vacuum hosesif faultyFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
20 steps · 4 stagesStage 1 of 4 Preparation and initial inspection 4 steps
- Ask the owner about the symptoms: whether the Check Engine light is on, rough idle, hesitation, poor acceleration, increased fuel consumption, hard starting, and under what conditions it happens (cold or hot engine, under load, in rain).
- Shut off the engine and open the hood. Check the oil and coolant levels and the condition of the battery. Low battery voltage causes false codes and ECU glitches.
- Inspect the engine bay: wiring harnesses for damage, signs of chafing, oil and moisture on connectors, and the security of the ground connections on the engine and body.
- Inspect the air intake path from the air filter to the throttle body and intake manifold. Rubber ducts and vacuum hoses must not be cracked, pinched, or detached. An air leak sharply changes intake pressure and causes rough running.
Stage 2 of 4 Reading codes 5 steps
- Find the OBD-II diagnostic connector inside the cabin on the driver's side under the dashboard. Connect the scanner with the ignition off.
- Turn the ignition on without starting the engine. Read the fault codes, including stored and pending ones. Write down all codes and the freeze frame data.
- Do not clear the codes right away. First look at which sensors and circuits are indicated. Examples from owners' experience: P0106 (manifold pressure sensor signal range), P1336 (crankshaft position sensor), and misfire codes for individual cylinders.
- If the scanner will not connect to the ECU, check the fuses for the ECU and diagnostic circuits, the power and ground at the OBD connector, and the integrity of the diagnostic line wire. No communication with a known-good scanner means a problem with the ECU power supply or the ECU itself.
- Clear the codes, warm up the engine, and repeat the check. If a code returns right away, the fault is permanent. If it does not return, the fault is intermittent: look for a poor contact.
Stage 3 of 4 Testing by symptoms and codes 8 steps
- Manifold pressure sensor (MAP, code P0106 and similar). It is located near the throttle body, on the throttle body housing or the intake manifold, and is connected by a small hose. First check the hose and look for vacuum leaks. Then inspect the connector and wires. The sensor itself cannot be repaired. If it is faulty, replace it as a unit.
- Crankshaft position sensor (code P1336). Check the sensor connector and wire, the gap and cleanliness of its tip, and the toothed reluctor wheel. If the code remains after replacing the ECU or the sensor, some vehicles require a learning (adaptation) procedure for the ECU based on the toothed ring, which needs a compatible scan tool.
- Misfires and hesitation. Remove the coils and spark plugs and assess the condition of the plugs (carbon deposits, oil, electrode wear). Replace the spark plugs as a set with the ones recommended for the engine, and take the gap and tightening torque from the service manual. Replace the coils with the same type that was installed, or as a set for all four cylinders.
- Fluctuating RPM and rev limiting. Check the idle air control valve and the throttle position sensor: disconnect the connectors, clean the contacts with electrical contact cleaner, and clean the throttle body with throttle body cleaner. Dirty contacts and a dirty throttle body often cause hesitation and loss of power.
- Check the connectors of the injectors, oxygen sensors, and the coolant temperature sensor: cleanliness, secure locking, and no corrosion. Use a multimeter to check the continuity of the wire from the sensor to the ECU and the presence of ground.
- If the scanner shows live data, watch the coolant temperature (it should be plausible after warm-up), idle RPM, and the throttle and intake pressure readings. Sharp jumps or values that do not change while the engine runs point to a faulty sensor or an open circuit.
- If you suspect the fuel system (poor starting, dips under load), check the fuel rail pressure with a gauge, the condition of the fuel filter, and the operation of the fuel pump. Take the pressure specifications from the service manual.
- If all sensors and circuits are fine and the mechanical side (compression, valve sealing) is normal, check the ECU power supply and grounds. The ECU is rarely the culprit and is replaced last.
Stage 4 of 4 Repair and verification 3 steps
- Replace one part at a time. After each replacement, clear the codes and check whether the error returns.
- Before working on connectors and sensors, disconnect the negative battery terminal. After reconnecting, check that the ECU communicates with the scanner.
- Take a 10-15 minute test drive in various driving modes. Then read the codes again and make sure there are no new or pending errors in memory and the Check Engine light is off.
Common mistakes and warnings
- Do not wash a hot engine with a pressure washer or pour a lot of water on it: the sudden cooling can permanently damage sensors
- Do not clear the codes without writing them down, or you will lose diagnostic data
- Do not replace the ECU until the sensors, wiring, and grounds have been ruled out
- Work on the fuel system away from open flame, and if you are inexperienced, take the car to a repair shop