← CS55

Changan CS55 1.5 (2019): Outer CV Joint Replacement

A failing outer CV joint shows up as a clicking or crunching noise when you turn the steering wheel under load while driving. The most common cause is a torn boot and loss of grease. The job is done with the driveshaft (axle shaft) removed. This guide covers the front axle. If the joint itself is intact and only the boot is torn, replacing the boot and grease is enough. The torque values below are approximate, so check the exact figures against the manufacturer's specifications.

DifficultyMedium Time2-3 hours per side Steps36

Parts

5
№PartAlternatives
01 Front outer CV joint for CS55, complete (with boot, retaining ring and grease)Find on Amazon → AlternativesGKNLobroSKF
02 Hub nut, newFind on Amazon →
03 Hub nut cotter pinif the nut is secured with a cotter pinFind on Amazon →
04 CV joint boot clampsnewFind on Amazon →
05 Ball joint cotter pins or self-locking nutnewFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

11

Step by step

36 steps · 5 stages
Stage 1 of 5 Preparation and access 5 steps
  1. Park the car on level ground, put it in gear (or P) and set the parking brake. While the wheels are still on the ground, slightly loosen the lug bolts and the hub nut: the axle nut is tightened very hard.
  2. Remove the hub cap, if there is one. If the hub nut is secured with a cotter pin, pull the pin out. If it is secured by staking, carefully bend the collar back.
  3. Have a helper press the brake pedal and loosen the hub nut with the socket and a long breaker bar. Do not unscrew it all the way yet.
  4. Raise the front of the car, set it on jack stands (never work under a car supported only by a jack), and remove the wheel.
  5. Remove the lower engine splash shield (if fitted) to access the inner CV joint and the transmission.
Stage 2 of 5 Disconnecting the suspension and removing the driveshaft 8 steps
  1. Unscrew the wheel speed (ABS) sensor from the knuckle or unclip its harness so you do not tear the wire.
  2. Remove the two caliper bolts, take off the caliper and hang it from the coil spring with wire. The caliper must not hang from the brake hose. Remove the brake rotor if it is held on the hub by a retaining clip or screw.
  3. Remove the ball joint nut (bend back or pull out the cotter pin if needed) and press the stud out of the steering knuckle with a separator. Alternatively, disconnect the bottom of the strut from the knuckle if that approach is more convenient on your trim level.
  4. Remove the hub nut completely and discard it (install a new one on reassembly).
  5. Swing the knuckle outward and pull the outer splined end of the driveshaft out of the hub. If the shaft is seized, tap the end with a soft-faced hammer through a drift. Do not hit the CV joint, and do not let the driveshaft hang from the inner joint.
  6. Place a drain pan under the transmission: a little oil will run out when the inner joint comes out of the gearbox.
  7. Pry with a pry bar between the inner joint housing and the transmission case (or the intermediate shaft bracket) and pull the inner end of the driveshaft out with a sharp tug. Hold the shaft by the joints and keep the inner end level so you do not damage the transmission seal.
  8. Plug the transmission opening with a clean rag and take the driveshaft to the workbench.
Stage 3 of 5 Replacing the outer cv joint 9 steps
  1. Clamp the shaft in the vise through soft jaws near the inner joint. Inspect both boots and the inner joint: their condition also determines whether additional replacement is needed.
  2. Loosen and remove the clamps on the outer boot, then slide the boot down the shaft toward the inside as far as the design allows.
  3. Wipe the old grease off the shaft and the joint. The CV joint sits on the shaft splines and is held by a retaining ring: mark its position for reassembly.
  4. Knock the joint off the shaft with a sharp hammer blow on the outer CV joint housing along the shaft axis (through a wooden spacer, never on the shaft itself). The retaining ring in the shaft groove compresses and releases from its seat.
  5. Remove the boot from the shaft and replace it with a new one (unless it comes with the new joint). Before sliding it on, wrap masking tape around the shaft splines so they do not cut the boot.
  6. Clean the shaft splines with a wire brush and inspect the retaining ring groove. Install a new retaining ring in the shaft groove.
  7. Fill the new CV joint with the grease from the kit (the amount is stated in the kit or on the packaging) and pack the remaining grease inside the boot.
  8. Slide the new boot and the small clamp onto the shaft, fit the joint onto the splines and drive it on with sharp blows through a soft spacer until the retaining ring clicks into place. Tug on it to check that the joint sits firmly and does not come off.
  9. Seat the boot on the joint housing and on the shaft in the proper grooves, then tighten the new clamps with a special clamp tool or crimping pliers. The boot must not be twisted or crushed: rotate the joint and move it through its full travel in both directions.
Stage 4 of 5 Installing the driveshaft 7 steps
  1. Check the transmission seal and lubricate its sealing lip. Replace the retaining ring on the inner end of the shaft if it is damaged.
  2. Insert the inner joint into the transmission until the retaining ring clicks into place. Pull on the joint housing (not the shaft) to check that it is locked.
  3. Lightly lubricate the splines on the outer end, swing the knuckle outward and insert the splines into the hub.
  4. Insert the ball joint stud into the knuckle and tighten the ball joint nut to the manufacturer's specification (a rough guide for this class of vehicle is 50-100 N·m (37-74 lb-ft)), then fit a cotter pin if the design uses one.
  5. Install the wheel speed (ABS) sensor after wiping its seat clean, and route the harness back into its clips.
  6. Install the rotor (if removed) and the caliper, and tighten the caliper bolts to the specification (a rough guide is 80-120 N·m (59-89 lb-ft)).
  7. Thread on the new hub nut, but do not fully tighten it yet.
Stage 5 of 5 Finishing and checking 7 steps
  1. Install the wheel, thread on the bolts and lower the car to the ground.
  2. Have a helper press the brake pedal, then tighten the hub nut with a torque wrench to the specified torque. The axle nut torque is very high (a rough guide for this class is 200-300 N·m (148-221 lb-ft)). Lock the nut with a cotter pin or by staking, as the design requires.
  3. Tighten the lug bolts in a crisscross pattern (a rough guide is 100-120 N·m (74-89 lb-ft)).
  4. Check the transmission oil level and top it up if needed with oil of the same specification.
  5. Install the splash shield and the hub cap.
  6. Pump the brake pedal several times so the pads seat against the rotor.
  7. Take a short test drive: at low speed, turn the steering wheel to full lock in both directions and listen for clicking or crunching. After 50-100 km, recheck the lug bolt torque and check for oil leaks from the transmission and the boots.

Common mistakes and warnings

  • Hub nut tightening and brake work are safety-critical: if you lack experience or a torque wrench, leave the job to a repair shop
  • Do not reuse the hub nut, and do not drive the car with an under-tightened nut: this destroys the wheel bearing
Spotted a mistake? Tell us →