Autopapyrus · Chevrolet Lacetti (J200)
https://autopapyrus.com/catalog/chevrolet/lacetti/guides/under-hood-fuse-and-relay-box-replacement/
https://autopapyrus.com/catalog/chevrolet/lacetti/guides/under-hood-fuse-and-relay-box-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Chevrolet Lacetti (J200): Under-Hood Fuse and Relay Box Replacement
The under-hood box is on the left side of the engine bay, between the coolant expansion tank and the battery, under a protective cover. Replace the whole box if the housing is damaged, the contacts are melted or burned out, and diagnostics confirm the box itself is faulty. The exact removal procedure for this specific car is not documented in publicly available service materials, so what follows is the general order of work and the box location. Work out the mounting details on the car.
Key figures
- ABS fuse (Ef2)the highest-rated fuse in the box; use exactly the same rating when replacing it (step 5)60 A
- Cooling fan fuses (Ef6, Ef8)do not mix them up when moving them to the new box (step 5)20 A and 30 A
- Number of relays in the boxafter replacement, check that the new box has the same number of sockets (step 9)11
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Complete under-hood fuse and relay box assembly for Lacetti J200Find on Amazon → | Alternativesgenuine GM/Daewooused box from the same car |
| 02 | Blade fuse setif neededFind on Amazon → | |
| 03 | Relays for the fuse boxup to 11 pcs, if neededFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
7
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
12 steps- Turn off the engine, remove the key, and wait a few minutes. Disconnect the negative terminal from the battery. The box is right next to it, and the power circuits in it are protected by 30-60 A fuses.
- Before replacing the box, make sure the fault is in the box itself and not elsewhere (a short in the wiring, an overloaded consumer). Otherwise the new box will fail the same way.
- Remove the box's protective cover. For access, you may need to move aside or remove the expansion tank without disconnecting the hoses, and remove the battery cover or terminal. If the battery is in the way, remove it together with its tray.
- Photograph the whole box: the layout of the relays and fuses, and the position of all connectors and power wires. Next to them in the box there is a slot for the fuse puller (PULLER).
- Remove all relays and fuses and lay them out in order. This keeps you from mixing up the ratings. Fuses Ef1-Ef31 have ratings from 10 to 60 A. For example, Ef2 (ABS) is 60 A, Ef6 and Ef8 (cooling fan) are 20 A and 30 A, and Ef5 is 30 A.
- Disconnect the power wires from the box terminals (the nuts on the battery and alternator circuits) and label each one. Do not let a wrench touch a terminal and the body at the same time.
- Press the locking tabs on each connector and disconnect them one at a time, labeling each with a marker or tape. If needed, use a thin screwdriver, taking care not to break the locks.
- Remove the fasteners holding the box to the body and lift the box up and out. If the box is held by clips, release them around the perimeter.
- Compare the old and new boxes: the shape, the number of sockets, the connector layout, the number of relays (11) and fuses (31, of which three are spares) must match. Move the relays and fuses to their places in the new box if they are in good condition. If the contacts are melted, replace those parts too.
- Install the box in reverse order: first secure it to the body, then connect the connectors according to your labels, then the power wires. Tightening torque for the power wire nuts and box fasteners: approximately 8-12 N·m (6-9 lb-ft) for the power terminals (check the exact values against the manufacturer's specifications). Do not overtighten, to avoid cracking the plastic housing.
- Install the protective cover, the expansion tank and the battery if you removed them, then connect the negative terminal.
- Check operation: engine start, low and high beams, horn, cooling fan (turn on the A/C), power windows, and make sure the ABS and airbag warning lights show no errors on the instrument cluster. Reset the clock and radio settings. Check for fault codes with a diagnostic scan.
Common mistakes and warnings
- Work only with the battery negative terminal disconnected
- High-current power circuits run through the box, and an accidental short with a wrench causes sparks, melting and a fire risk
- Do not install a fuse with a higher rating than specified, as it will overheat the wiring
- If you have no experience with automotive electrical systems, it is better to leave the job to a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Chevrolet Brand
Chevrolet (Chevrolet Motor Division), a name known around the world, is a division of General Motors that builds…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →