← Town & Country

Chrysler Town & Country 3.8 (2004): Parking Brake Adjustment

On the Town & Country, the parking brake pedal is on the left, and the shoes are located inside the rear brake rotor, forming a drum-in-hat design. The cables self-adjust, but the shoes do not adjust themselves and are set manually with the star wheel. You need to do this after replacing the brake pads, rotors or cables, and when the vehicle does not hold well on a slope. The job is done at each rear wheel.

DifficultyMedium Time1-1.5 hours Steps19

Key figures

  • Lug nut tightening torqueon the torque wrench in step 15, first half of this torque, then full torque
    135 N·m (100 lb-ft)
  • Gauge clearancethe amount by which the gauge is set smaller than the measured drum diameter before adjustment (step 8)
    1/64 inch
  • Pedal presses after adjustmentpress and release the pedal so the cables seat and self-adjust (step 17)
    1 time

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the parking brake shoes and adjuster star wheel are

Parking brake shoes with the disc removed1Parking brake shoes4Shoe bracket2Gauge for measuring drum diameter(diagonally)3Hub with studs5Adjuster star wheelView from the wheel side: disc and caliper removedTap to enlarge
  1. 1Parking brake shoes on the bracket (inside the disc 'hat'): spread them with the star wheel until the linings touch the gauge jaws.
  2. 2Drum gauge: its jaws hug the shoes from outside diagonally, one on the top shoe and one on the opposite bottom shoe, at the widest point. Set it 1/64 in smaller than the measured diameter.
  3. 3Hub with studs: after adjusting, the disc goes on it, then the wheel.
  4. 4Shoe bracket: the shoes are mounted on it, and the caliper bolts to it.
  5. 5Adjuster star wheel: between the shoe ends. Turn it with a screwdriver or hook; if the disc drags, back it off one tooth.

Part

№Part
01 Drum-in-hat parking brake shoe set (built into brake rotor) with springsif worn or oil-contaminated; both sides of the axle, 2 setsFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8

Step by step

19 steps · 5 stages
Stage 1 of 5 Preparation 3 steps
  1. Park the vehicle on a level surface and chock the front wheels. Make sure the parking brake pedal is fully released. If the pedal is applied, the shoes cannot be adjusted accurately.
  2. Loosen the lug nuts on the rear wheel, raise the rear of the vehicle and set it on jack stands.
  3. Remove the wheel.
Stage 2 of 5 Accessing the shoes 2 steps
  1. Remove the caliper adapter bolts and take the caliper off the bracket. Hang it with wire so the hose is not stretched. For reassembly, use the torque specified by the manufacturer for the caliper bolts.
  2. Remove the brake rotor from the hub. Inside the rotor "hat" is the parking brake drum surface, and on the bracket are the shoes with the adjuster star wheel.
Stage 3 of 5 Adjustment 7 steps
  1. Use the drum diameter gauge to measure the inside diameter of the drum section of the rotor. Measure in the middle of the strip where the shoes contact the surface.
  2. Read the measurement from the gauge with the ruler with 1/64 inch graduations.
  3. Reduce this measurement by 1/64 inch and reset the outer jaws of the gauge to the new dimension.
  4. Place the gauge over the shoes diagonally: on top of one shoe and at the bottom of the opposite shoe, at the widest point.
  5. Turn the adjuster star wheel until the shoe linings just touch the gauge jaws. Then check the dimension in both diagonal positions and fine-tune if necessary.
  6. Install the rotor on the hub. If needed, hold it in place with a couple of lug nuts.
  7. Rotate the rotor by hand. The shoes must not drag on the drum. If they drag, remove the rotor, back off the star wheel by one tooth and check again. Repeat until there is no drag.
Stage 4 of 5 Reassembly 3 steps
  1. Install the caliper on the bracket and tighten the bolts to the torque specified by the manufacturer.
  2. Install the wheel and thread on the lug nuts by hand.
  3. Lower the vehicle onto its wheels and tighten the lug nuts in a crisscross pattern in two stages: first to half torque, then to the full torque of 135 N·m (100 lb-ft).
Stage 5 of 5 Check 4 steps
  1. Repeat steps 2-15 on the other rear wheel.
  2. Press and release the parking brake pedal once. This seats the cables and they self-adjust. There is no separate manual cable adjustment.
  3. Press the service brake pedal several times until it feels firm before driving off.
  4. Test the parking brake on a slight slope: the vehicle must hold. Then take a test drive; the wheels must not get hot or drag when the pedal is released.

Common mistakes and warnings

  • The parking brake affects safety
  • If you have no experience working on brakes, leave the job to a repair shop
  • After the work, be sure to check that the vehicle holds on a slope
  • If the shoes are contaminated with oil or badly worn, adjustment will not help and they must be replaced
  • Never work under a vehicle that is supported only by a jack
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →