https://autopapyrus.com/catalog/citroen/berlingo/guides/diagnosis-engine-cranks-but-won-t-start/
Citroën Berlingo 1.6 (2012): Diagnosis — Engine Cranks but Won't Start
If the starter turns the engine over normally but it won't fire, the cause almost always falls into one of three categories: no fuel or no rail pressure, the engine control unit can't see crankshaft and camshaft synchronization, or the immobilizer or a loss of communication between modules is blocking the start. The checks go from simple to complex. The steps below are written for the 1.6 HDi diesel. For the 1.6 gasoline version, the specific checks are listed in step 11.
Diagram: where the 1.6 HDi diesel fuel filter is and what to inspect on it
- 1Round cover with a cap on top: this is the diesel fuel filter housing. It has a water trap; replace the filter if it is overdue or clogged.
- 2Fuel hoses with white quick couplings: inspect them and their connections to the filter for leaks and wet traces, since air gets in there.
- 3Two electrical connectors on the filter top plate: check the plugs and wires for corrosion and chafing.
- 4Black air box right next to the filter: a landmark to find the filter.
- 5Cast aluminium housing left of the filter: a landmark.
- 6Metal bracket with bolts above the connectors: a landmark.
Parts
8| № | Part |
|---|---|
| 01 | Diesel fuel filter (1.6 HDi)if faultyFind on Amazon → |
| 02 | Crankshaft position sensorif faultyFind on Amazon → |
| 03 | Fuel rail pressure sensorif faultyFind on Amazon → |
| 04 | High-pressure pump pressure regulatorif faultyFind on Amazon → |
| 05 | Glow plugs (diesel)if faultyFind on Amazon → |
| 06 | Glow plug control relay (diesel)if faultyFind on Amazon → |
| 07 | Spark plugs (1.6 gasoline)if faultyFind on Amazon → |
| 08 | Ignition coils (1.6 gasoline)if faultyFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 7 more.
See manuals →
Step by step
12 steps- Assess how the starter is turning the engine. If it cranks slowly, check the battery and terminals first: that is a power supply problem, not a fuel problem. If it cranks briskly and evenly, move on.
- Look at the instrument cluster when you switch the ignition on. Is the immobilizer icon or the key with a lock lit, is the engine warning light flashing, does the glow plug indicator stay on? Write down what you see. Try the spare key and check the battery in the key fob.
- Connect the scanner and read the engine and BSI (built-in systems interface) fault codes. Pay attention to codes for low rail pressure, the crankshaft sensor, the glow plug circuit and communication between modules (CAN). A loss-of-communication fault between the engine control unit and the BSI is serious: with it, the engine does not receive permission to start. Cheap universal scanners can't read much on PSA vehicles, so if the codes won't read, you need a diagnostic tool for this make.
- Check the fuel level in the tank by the actual amount of fuel, not by the gauge: with a nearly empty tank, a diesel easily takes in air. If the fuel hasn't been changed in a long time or the car has been sitting, check the fuel for water: drain 0.5-1 L (0.53-1.06 qt) from the filter or take a sample from the tank into a clear jar and leave it overnight. Water or a cloudy emulsion at the bottom means the fuel must be drained and the filter replaced. Water in the tank settles overnight and blocks the fuel pickup, and after priming the engine may start briefly and then stall again.
- Check for air leaks. Signs: the engine starts only after priming, and in the morning the fuel "drains" back into the tank. Inspect the rubber fuel hoses and their connections at the filter, the priming bulb and the high-pressure pump, looking for seepage and wet traces. Air most often gets in through old hoses, seals and the filter housing.
- Prime the fuel system with the priming bulb (located on the engine under a plastic cover). Pump until the bulb feels firm. If the bulb stays "empty" after being pressed and quickly collapses, air is getting into the line, or the bulb's own valves aren't holding. The bulb only primes the low-pressure side; it does not fill the rail.
- Replace the fuel filter if it is overdue for replacement or clogged: the housing has a water separator. After replacing it, prime the system again and try starting. Do not crank the starter continuously for longer than 10-15 seconds: take breaks, otherwise the battery will drain and the starter will overheat.
- Check the crankshaft position sensor: it is located at the crankshaft pulley (roughly at the bottom, in the "7 o'clock" position when looking at the pulley). Inspect the connector and wiring for breaks, corrosion and chafing. The control unit compares the crankshaft and camshaft signals and cuts off fuel delivery if they disagree, so a faulty sensor or connector produces exactly this symptom: the starter cranks, the engine doesn't start. Check the sensor's resistance and acceptable values against the manufacturer's specifications.
- Check the fuel rail pressure on the scanner while cranking (live data). If the pressure clearly doesn't rise while cranking and stays near zero, the cause may be the high-pressure pump pressure regulator, the rail pressure sensor, the pump itself, or air and water on the low-pressure side. Check the acceptable pressure values against the manufacturer's specifications. Do not work on high-pressure lines without experience: the pressure in the system is very high.
- Check the injectors if everything above is normal: an injector return-flow (leak-off) test shows whether any injector is leaking and preventing pressure from building. This is a job for a repair shop with the right equipment. Also check the fuses in the engine compartment box and the cabin fuse box, the engine control unit connectors for corrosion, and look for signs of moisture under the floor mats and at the base of the windshield (the BSI is vulnerable to water).
- If you have the 1.6 gasoline engine: check whether the fault codes include misfires and the crankshaft sensor, whether you can hear the fuel pump hum when you switch the ignition on, and whether the spark plugs are flooded after repeated start attempts. Remove the spark plugs and inspect them: wet plugs mean flooding; dry plugs mean no fuel or no spark. Compare the spark plugs and coils against the manufacturer's specifications for type and gap.
- After fixing the cause, clear the fault codes, prime the system, do a test start and confirm that the engine starts on the first attempt both cold and warm.
Common mistakes and warnings
- The Common Rail diesel system operates at very high pressure: do not loosen high-pressure fittings and fuel lines on a running engine or one that has just been running, and loosen lines only after relieving the pressure, while wearing gloves
- Do not use starting fluid unless necessary: on a diesel it can damage the engine
- If the simple fuel and sensor checks don't help and the fault codes point to a loss of communication between modules or to the high-pressure pump and injectors, take the car to a repair shop with PSA diagnostics: this requires specialized equipment
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Citroën Brand
Citroën is an automaker founded in France in 1919 by André Citroën. Since 1976 it has been part of the PSA Peugeot…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →