← Logan Dacia Logan repair manuals →

Dacia Logan 1.0 SCe (2022): Engine Condition Diagnosis

The B4D 1.0 SCe engine is a naturally aspirated 3-cylinder with 12 valves, an aluminum block and a chain-driven timing system. Its condition is assessed through engine control unit fault codes, compression, oil traces, noise, smoke and cooling system checks. The engine has no hydraulic lifters, so valve lash must be checked according to the maintenance schedule.

DifficultyMedium Time1.5-3 hours Steps14

Key figures

  • Spark plug tightening torqueset on the torque wrench when installing the plugs (step 12); more than that risks stripping the threads in the aluminum head
    24-25 N·m (18 lb-ft)
  • Spark plug socket sizeneeded to reach the plug in the well (step 8)
    14 mm (long and thin)
  • Oil capacityfor checking the level and topping up (step 3)
    about 3.0 L (3.2 qt), 5W-40
  • Valve lash check intervalthere are no hydraulic lifters, so the lash is adjusted periodically (step 5)
    about 100,000 km (62,000 mi)

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

4
№PartAlternatives
01 5W-40 engine oilabout 3.0 L (3.2 qt)Find on Amazon →
02 Oil filter for 1.0 SCeFind on Amazon →
03 Spark plugs for B4DFind on Amazon → AlternativesNGKDensoBosch
04 Valve cover gasketif leakingFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more. See manuals →

Step by step

14 steps
  1. Talk to the owner and review the service history: when the oil was last changed, whether the engine has overheated, and whether there is oil consumption, unstable idle, hesitation or hard starting. Overheating is especially dangerous for an aluminum engine, so find out about it first.
  2. Inspect the engine cold. Check for oil and coolant leaks (valve cover, oil pan, crankshaft seal, hoses, water pump, radiator), the condition of the accessory drive belt and the engine mounts.
  3. Check the oil level and condition on the dipstick. Dark oil is not a problem by itself. A "milky coffee" emulsion indicates coolant contamination, and metallic particles indicate wear. Check the coolant level in the expansion tank (with the engine cold) and look for an oil film on the coolant.
  4. Connect the OBD scanner. Read active and stored fault codes, the monitor readiness status, fuel trims (long term and short term) and the coolant temperature. Large positive trims point to an air leak or fuel shortage, and per-cylinder misfires point to spark plugs, ignition coils or compression.
  5. Start the engine cold and listen. A brief noise in the first seconds is typical for a chain-driven timing system. Chain rattle that does not go away after warm-up requires further inspection of the tensioner and the chain. Valve ticking may mean excessive valve lash: there are no hydraulic lifters, and the lash is adjusted periodically (as a guide, about 100,000 km (62,000 mi); check the exact interval against the manufacturer's maintenance schedule).
  6. Warm the engine up to operating temperature. Check that the idle is stable, that the radiator electric fan switches on and that there is no smoke: thick white smoke means coolant in the combustion chamber, blue means oil, and black means a rich mixture.
  7. Prepare for the compression test. Turn the engine off, disconnect the connectors from the ignition coils and disable the fuel pump (fuse or relay, according to the fuse box diagram) so the cylinders are not flooded with fuel. Blow out the spark plug wells with compressed air or wipe them clean so that dirt does not fall into the cylinder.
  8. Remove the spark plugs one at a time with a long, thin 14 mm socket, after removing the ignition coils first (the coils are held by bolts; torque per the manufacturer's specification). Inspect the plugs: an even light-gray deposit is normal, black oily electrodes mean worn valve stem seals or rings, a white deposit means a lean mixture, and plugs wet with gasoline mean ignition problems.
  9. Screw the compression tester into the first cylinder, with the throttle fully open crank the engine with the starter for 5-6 revolutions and record the maximum pressure. Repeat for the other cylinders. The compression specifications for the B4D are not confirmed, so use the value from the manufacturer's service data. Evenness matters more: a difference of more than 10-15% between cylinders is a sign of wear or leaking valves.
  10. If one cylinder shows a low reading, pour 10-15 ml (0.3-0.5 fl oz) of engine oil into it and repeat the measurement. If the pressure rises, the piston rings or piston group are worn. If it does not change, the problem is in the valves or the cylinder head gasket. Low pressure in two adjacent cylinders points to the head gasket.
  11. If you suspect a coolant leak into the cylinders, pressure-test the cooling system and compare the color and smell of the gases coming out into the expansion tank on a warm engine.
  12. Install the spark plugs. Check the gap and type against the manufacturer's specification and choose them from the catalog for the B4D. Thread them in by hand first so you don't strip the threads, then tighten with a torque wrench to 24-25 N·m (18 lb-ft) (for 3-cylinder engines of this family). Lightly lubricate the coil boots with universal grease, install the coils and connect the connectors.
  13. Restore the fuel pump, start the engine, wait for the fuel trim to stabilize, and clear the stored fault codes that appeared during the diagnosis (disconnected coils, pump).
  14. Summarize the results: compare the OBD codes, compression, oil and spark plug condition, noises and leaks. If chain wear, a drop in compression or coolant in the oil is found, plan further repairs at a repair shop. This work requires disassembling the engine.

Common mistakes and warnings

  • Do not crank the engine with the starter with the spark plugs removed unless the fuel pump and ignition coils are disconnected: this floods the cylinders with gasoline and can damage the catalytic converter and the coils
  • A hot engine and the radiator fan are dangerous, so keep your hands and clothing clear
  • Overheating an aluminum engine can warp the cylinder head, so if there are signs of overheating, do not drive the car until it has been diagnosed
  • Check tightening torques, spark plug gap and compression specifications against the manufacturer's service data
Spotted a mistake? Tell us →