← XF

DAF XF MX-13 (2017): Cylinder Head Height and Flatness Check

The minimum cylinder head height is the limit thickness of the head between the block mating surface and the valve cover surface. If it is below spec, the head must not be resurfaced or reinstalled and must be replaced. The exact numeric value for the MX-13 is not confirmed in public sources, so check it against the manufacturer's service manual.

DifficultyHard Time1-2 hoursmeasurement on a removed head Steps12

Parts

3
№Part
01 MX-13 top overhaul gasket set (includes cylinder head gasket)Find on Amazon →
02 MX-13 cylinder head bolts (new, single-use)set per cylinder headFind on Amazon →
03 MX-13 cylinder head assemblyif neededFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5

Step by step

12 steps
  1. Remove the cylinder head according to the service manual: drain the coolant, remove the valve cover, rocker arms and pushrods or crossheads, injectors, and manifolds. Before removal, mark the position of the parts so you can return them to their original places.
  2. Loosen the head bolts in the reverse of the tightening sequence, in several passes. Remove the head together with the gasket and place it on a flat, clean surface.
  3. Thoroughly clean the mating surface of gasket residue and carbon deposits. Do not use abrasives or sharp scrapers that leave scratches. Wipe the surface with cleaner.
  4. Check flatness. Place the straightedge along the head, then across it and along both diagonals. Use a feeler gauge to measure the gap between the straightedge and the surface. The allowable flatness deviation is given in the manufacturer's service manual; if it is exceeded, the head must not be returned to service.
  5. Inspect the surface for cracks, signs of gas blow-by, and erosion around the valve seats and coolant passages. A crack between the valve seats or near the injector bore means the head must be replaced.
  6. Measure the head height: use a caliper or micrometer from the mating surface to the upper machined surface. Measure at several points (at the corners and in the middle) and use the smallest value. Take all measurements on a cold head at room temperature.
  7. Compare the result with the minimum allowable height from the service manual. If the measured height is below the minimum, the head is rejected. If the value is right at the limit, the head has reached the end of its service life, and it makes more sense to install a new one.
  8. Decide on milling or grinding the surface only according to the service manual. For MX-13 heads, removing metal is generally not provided for, because it changes the height, compression ratio, and valve clearances. If removal is permitted, the amount must not bring the height below the minimum.
  9. Before assembly, check the cylinder block surface: flatness, cleanliness, and the condition of the head bolt threaded holes. Blow out the holes and remove any oil and coolant from them.
  10. Place the new gasket on the block without lubricant or sealant unless the service manual requires them. Check the marking and thickness of the gasket against what your engine requires. The correct gasket is determined by the service manual and by measuring piston protrusion.
  11. Install the head. Tighten the new bolts in the sequence specified in the service manual, in several passes: first to the initial torque, then by turning through the specified angle. Take the torque and angle values from the manufacturer's service manual, and use a torque wrench and an angle gauge.
  12. Reassemble the attached components, adjust the valve and injector clearances according to the service manual, fill with coolant, warm up the engine, and check the gasket for leaks and for any seepage.

Common mistakes and warnings

  • A head with a height below the minimum or with excessive warpage leads to gas blow-by, overheating, coolant getting into the oil, and repeated gasket failure
  • The head bolts are single-use, so do not reuse them
  • If you have no experience with diesel engine overhauls, leave the measurement and assembly to a specialized repair shop
Spotted a mistake? Tell us →

Our articles

More articles →