← Terios Daihatsu Terios repair manuals →

Daihatsu Terios 0.7 EF-DEM (2004): Valve Replacement and Valve Seat Lapping on the Cylinder Head

This job is done with the cylinder head removed. The new valves are lapped to the seats, and the seats and guides are checked for wear. The engine is a compact three-cylinder, but the procedure is standard. I couldn't find exact factory values for the EF-DEM (torque specs, valve dimensions, clearances) in reliable public sources. The figures below are approximate, so check the exact values against the manufacturer's service manual.

DifficultyHard Time1-2 daysremoving and installing the head takes 4-6 hours; the rest is inspection and valve work Steps21

Diagram: where the valves and seats are in the cylinder head

View of the head from the cylinder block side2Valve seat (ring)1Valve (head)4Head bolt (hole)5Gasket surface3Spark plugThree cylinders, each with 4 valves and a spark plug in the centreTap to enlarge
  1. 1Valve: the valve head in the combustion chamber. Remove it with a spring compressor, then lap the new one to the seat with paste. Each cylinder has 4 valves.
  2. 2Seat: the light ring around the valve. Check it for pits, cracks and burn; seat work is done only on a machine.
  3. 3Spark plug in the centre of the cylinder between the valves: a landmark so you don't mix up cylinders.
  4. 4Head bolt hole: loosen bolts from the edges to the centre, tighten from the centre to the edges.
  5. 5Head surface for the gasket: clean with a plastic scraper without scratching the aluminium, check with a ruler and feeler gauge.

Parts

10
№Part
01 Intake and exhaust valve set for EF-DEMFind on Amazon →
02 Valve stem seal setFind on Amazon →
03 Cylinder head gasketFind on Amazon →
04 Cylinder head bolt setif the bolts are single-useFind on Amazon →
05 Valve cover gasketFind on Amazon →
06 Intake and exhaust manifold gasket setFind on Amazon →
07 Timing belt or chainFind on Amazon →
08 CoolantFind on Amazon →
09 Engine oilFind on Amazon →
10 Oil filterFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

11
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

21 steps
  1. Disconnect the negative battery terminal. Drain the coolant from the radiator and the engine block. Be sure to let the engine cool down first: a hot aluminum head can warp.
  2. Remove the air filter with its ducts. Disconnect the cooling system and crankcase ventilation hoses, the throttle cable, the sensor connectors and the wiring. Photograph or label everything you disconnect.
  3. Disconnect the exhaust manifold from the downpipe (soak the nuts with penetrating oil ahead of time). Remove the intake manifold together with the throttle body and the fuel rail (relieve the fuel system pressure first). If the engine has a turbocharger, remove it together with the manifold and cover all open passages with clean plugs.
  4. Remove the valve cover. Set the No. 1 cylinder piston to TDC on the compression stroke using the timing marks. Remove the timing drive from the camshaft, first marking the position of the belt or chain relative to the sprockets, and hang it so that it does not sag or bend sharply.
  5. Loosen the head bolts in 2-3 stages from the edges toward the center, in the reverse of the tightening sequence. Remove the head. Do not pry it apart with a screwdriver at the mating surface; if needed, tap it lightly with a rubber mallet. Remove the camshaft and the rocker arms (or lifters), and lay out each part in order so it can go back in its original position.
  6. Clean the head surface of gasket residue with a plastic scraper, taking care not to scratch the aluminum. Check flatness with a straightedge and feeler gauge; if the head is warped, send it out for resurfacing. For the allowable warpage, see the manufacturer's service manual.
  7. Remove the valves: compress the spring with the valve spring compressor, take out the keepers, then remove the retainer, the spring and the valve. Place the valves in order by port (cylinder number, intake or exhaust) so they don't get mixed up. Remove the valve stem seals; they must be replaced.
  8. Clean the combustion chambers and ports of carbon deposits. Inspect the seats for pitting, cracks, burning, and a wide or uneven contact band. Measure the clearance between the valve stem and the guide (micrometer and bore gauge). If the clearance exceeds the limit, the guides are replaced, and damaged seats are either reground or replaced. This is machine work done at a cylinder head machine shop.
  9. Before lapping, compare the new valves with the old ones: head diameter, length and stem diameter. The valves must be specifically for the EF-DEM; intake and exhaust valves differ.
  10. Lapping: apply a thin layer of coarse compound to the valve face, lubricate the stem with engine oil and insert the valve into the guide. Using the suction-cup tool, rotate the valve back and forth through a quarter to a half turn, periodically lifting and repositioning it. Do not apply compound to the stem.
  11. When an even, matte contact band without pitting appears on the seat and the valve face, switch to fine compound and continue until you have an even gray ring. Thoroughly remove the compound from the head and wash out the guides and ports.
  12. Check the contact pattern: mark the valve face with several pencil lines across it, insert the valve and turn it a quarter turn. The marks should be erased evenly around the whole circumference. Alternatively, pour kerosene into the port and check that it does not seep past the valve head over several minutes.
  13. Install the new valve stem seals (lubricate them with oil and fit them carefully, without cocking them). Assemble the valves: lubricate the stem, insert the valve, then fit the spring, retainer and keepers. Tap the valve tip lightly to make sure the keepers have seated.
  14. Install the camshaft and rocker arms in their original positions, and tighten the caps or bearing supports evenly in the sequence given in the service manual. Check the torque for these parts against the manufacturer's service manual; a rough guide for small-displacement Daihatsu engines is about 10-25 N·m (7-18 lb-ft), so confirm the exact value.
  15. Wipe the block surface clean, and blow out and dry the bolt holes. Fit a new head gasket (without sealant unless specified otherwise), right side up, lining up all the holes. Install the head.
  16. Tighten the head bolts in several stages, working diagonally from the center outward, using a torque wrench. For engines in this series, a final torque of around 40 N·m (30 lb-ft) is approximate; check the exact torque and whether an angle turn is needed against the manufacturer's service manual. If the bolts are designed for single use, replace them.
  17. Install the timing drive strictly by the marks (No. 1 cylinder at TDC), check that the marks on the crankshaft and camshaft line up, and turn the crankshaft two full revolutions by hand, then check the marks again. Adjust the belt or chain tension according to the service manual.
  18. Check and, if necessary, adjust the valve clearances (cold engine, piston at TDC on the compression stroke). Check the clearance values against the manufacturer's service manual. If the clearances are adjusted by selecting shims or lifters, go by the values in the manual.
  19. Install the valve cover with a new gasket and tighten the bolts in a crisscross pattern, lightly (a light torque, about 5-10 N·m (4-7 lb-ft) per the manufacturer's service manual). Fit the manifolds with new gaskets, then connect the sensors, hoses and throttle cable.
  20. Fill with coolant and bleed the air from the system. Change the engine oil and oil filter, since coolant or dirt may have gotten into the oil. Connect the battery.
  21. Start the engine and warm it up to operating temperature, watching for leaks and checking that it runs smoothly. Recheck the coolant level. After the first 500-1000 km (300-600 miles), check the oil and coolant levels and, if necessary, retighten fasteners per the service manual.

Common mistakes and warnings

  • Do not mix up the valves or their positions, never lap a valve dry, and do not let abrasive compound get into the guide or the ports
  • Be sure to wash the head thoroughly
  • Work on the seats and guides (boring, replacement, cutting) should be done only on a machine; do not attempt it yourself
  • If you have no experience with valve timing, have a specialist set the timing marks: misaligned marks cause the pistons to hit the valves
  • The torque values in this guide are approximate, so be sure to check them against the manufacturer's service manual
Spotted a mistake? Tell us →