https://autopapyrus.com/catalog/dodge/caravan-grand-caravan/guides/diagnosing-and-repairing-the-hazard-warning-lights-hazard-flashers/
Dodge Grand Caravan (2003): Hazard Warning Light Diagnosis and Repair
Hazard light problems on this minivan usually come down to four causes: burned-out bulbs, a blown fuse or flasher relay, poor connector contact under the dash, or a worn steering column multifunction switch. Check the simple things first (bulbs, fuses, connectors), then the switches. This guide covers the hazard system as a whole, for when the exterior lights do not flash. If only the turn signals fail, or only one side, the diagnosis is the same.
Key figures
- Normal flash rateabout 90 flashes per minute, which is how fast the hazards of a healthy vehicle should flash (step 4, step 17)
- Double-speed flashingabout 180 per minute, a sign of a burned-out bulb or a break on that side (step 4)
- Rear lamp mountingtwo bolts, 10 mm socket, removed to access the bulbs (step 5)
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the fuse block is and what to check in it
- 1Combined flasher module: after disconnecting the negative terminal, pull it out and check the pins for soot and overheating.
- 2Fuses: check the turn signal, hazard and parking light circuits using the diagram on the block cover; test suspect ones with a multimeter or test lamp.
- 3The whole fuse block (orange dashed): in the cabin left of the steering column; wiggle the connectors near it, floating contacts occur there.
- 4Relays: two rows, four large and four small. There is more than one.
Parts
5| № | Part | Alternatives |
|---|---|---|
| 01 | Turn signal bulbs (dual-filament, type 3157 in rear lamps)if faultyFind on Amazon → | |
| 02 | Combined turn signal/hazard flasher moduleif faultyFind on Amazon → | |
| 03 | Fusesif faultyFind on Amazon → | |
| 04 | Dash-mounted hazard switchif faultyFind on Amazon → | |
| 05 | Steering column multifunction switchif faultyFind on Amazon → | AlternativesDormanMopar |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
19 steps · 5 stagesStage 1 of 5 Identifying the symptom 4 steps
- Turn the ignition on and press the hazard button. Listen for the flasher relay clicking and watch whether the indicator arrows in the instrument cluster flash.
- Get out of the vehicle and check all four corners (front and rear lights, side marker lights). Note which lights do not work.
- Switch on the left turn signal, then the right. If the turn signals work but the hazards do not, the fault is in the hazard button or its circuit. If nothing works, but the cluster arrows flash and the relay clicks, look for a break in the circuit to the exterior lights (fuse, connector, switch).
- Use the flash rate as a reference: normal is about 90 flashes per minute. A doubled rate (about 180) means a burned-out bulb or a broken wire on that side.
Stage 2 of 5 Bulbs and fuses 4 steps
- Open the liftgate, remove the two lamp mounting bolts (10 mm socket), pull the lamp assembly rearward and disconnect the connector. Tighten the bolts by hand with light force, since the plastic housing cracks easily.
- Turn the bulb socket counterclockwise and pull out the bulb. Check the socket for corrosion and blackened contacts; clean them and apply dielectric grease. Do not touch the glass of the new bulb with your fingers.
- Check the front turn signal bulbs the same way. It is best to replace bulbs in pairs on the same side.
- Locate the fuse boxes (inside the cabin to the left of the steering column, and the under-hood box). Check the fuses for the turn signal, hazard and parking light circuits using the diagram on the box cover. Test any suspect fuses with a multimeter or test light.
Stage 3 of 5 Flasher relay and connectors 4 steps
- If your trim level has a separate combined flasher module, it is usually located in the fuse box to the left of the steering column. To reach it, remove the lower steering column cover and the lower panel (knee bolster).
- Disconnect the negative battery terminal. Pull out the module and inspect the pins for carbon buildup and signs of overheating.
- Wiggle the module connectors and the connectors under the dash near the fuse box: this model is known for intermittent contacts, and wiggling may bring the hazards back. Clean them and apply dielectric grease.
- Reconnect the battery and turn on the hazards. Clicking with no flashing of the exterior lights points to the circuit after the module. No click with good fuses and power points to the module itself.
Stage 4 of 5 Switches 3 steps
- Hazard button: carefully pry off the trim panel around the button on the center console with a trim tool, pull out the button and disconnect the connector. Check with a multimeter in continuity mode that the button closes the contacts when pressed. Replace a faulty button as a complete unit.
- Multifunction switch (the steering column stalk for turn signals and lights): it sends ground signals for the turn signals and hazards to the module. If both the turn signals and the hazards fail, the cause is most often this switch. Check the connector and the switch contacts with a continuity test following the wiring diagram.
- Replacing the multifunction switch involves working near the airbag and the steering wheel clockspring. Before starting, disconnect the battery and wait the time specified by the manufacturer for the safety system to discharge. Look up the steering wheel and airbag fastener torque specs in the manufacturer's service information; if you lack experience, leave this job to a repair shop.
Stage 5 of 5 Reassembly and testing 4 steps
- Reassemble the panels and covers, install all the lamps, and reconnect the battery.
- Turn the ignition on and test the hazards and both turn signals; make sure the lights flash on all sides at about 90 flashes per minute.
- Test the hazards with the ignition off: they should work in this mode.
- If nothing works even after replacing the bulbs, fuses, module and switches, have the body control module checked with a scan tool.
Common mistakes and warnings
- Work near the steering column involves the airbag: do not remove the steering wheel or airbag module while the battery is connected
- The hazard lights are a safety feature; do not drive on the road with faulty turn signals or hazards
- If you have no experience with SRS (airbag) systems, take the vehicle to a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Dodge Brand
Dodge is an automotive brand under the Chrysler umbrella. It has produced passenger cars as well as trucks, crossovers…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →