Autopapyrus · FAW Besturn T99 2.0 Turbo (2023)
https://autopapyrus.com/catalog/faw/besturn-t99/guides/boost-pressure-sensor-replacement/
https://autopapyrus.com/catalog/faw/besturn-t99/guides/boost-pressure-sensor-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
FAW Besturn T99 2.0 Turbo (2023): Boost Pressure Sensor Replacement
The boost pressure sensor is installed in the intake tract downstream of the turbocharger and intercooler. It sends the intake pressure to the engine control unit. When it fails, you get sensor circuit codes, a loss of power, and possibly limp mode. The sensor is usually held by a clip or two small screws, so replacement takes only a few minutes. The exact mounting arrangement and tightening torque for the T99 are not given in publicly available materials, so the general procedure is described below.
Key figures
- Normal sensor reading with the ignition on and the engine offabout 1000 mbar. Use it to check the sensor on the scanner before replacement and after it (step 11)
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
2| № | Part |
|---|---|
| 01 | Boost pressure sensor (with intake air temperature sensor) for 2.0 Turbo 224 hp engineFind on Amazon → |
| 02 | Boost pressure sensor O-ringincluded with the sensorFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Step by step
12 steps- Park the car on level ground, set the parking brake, turn the ignition off, and let the engine cool down. The intake is hot and it's easy to get burned.
- Open the hood. Remove the decorative engine cover if it blocks access.
- Locate the sensor. It is mounted on the intake manifold or on the pipe between the intercooler and the throttle body, and it has a small connector with 3-4 wires.
- Before replacing it, inspect the intake tract. Check the boost hoses, clamps, and intercooler pipes for cracks, oil seepage, and loose clamps. A charge air leak causes the same symptoms as a faulty sensor.
- Press the connector lock and disconnect the plug. Pull on the connector body, not on the wires.
- Remove the sensor. If it is held by a clip, press the side tabs and pull it out of its seat. If it is held by screws, remove them and take the sensor out, rocking it gently.
- Make sure the old O-ring has not stayed in the seat. There should be only one ring. Wipe the mounting surface with a clean rag so that no dirt gets into the intake.
- Compare the new sensor with the old one for shape, connector, and pressure range. A sensor with a different range will fit and connect, but it will show the wrong pressure, and the code will come back.
- Lightly lubricate the O-ring of the new sensor with clean engine oil. Insert the sensor until it clicks or bottoms out. If it is held by screws, tighten them without excessive force. The exact torque is per the manufacturer's specification and is roughly a few N·m, so do not overtighten the plastic housing.
- Push the connector on until it clicks and check that the lock is seated. Reinstall the decorative cover.
- Connect the scanner, read the codes, and clear them. Start the engine, let it idle, and make sure no new codes appear.
- Take a test drive with smooth throttle application. If limp mode persists or the code returns, recheck the intake for leaks and check the sensor connector.
Common mistakes and warnings
- Before replacing the sensor, make sure the sensor is actually the cause
- To do this, check the live data on the scanner
- With the ignition on and the engine off, the pressure should be close to atmospheric, about 1000 mbar at sea level
- If the sensor is oily, you can clean it with electrical contact cleaner
- Heavy oil contamination points to a crankcase ventilation problem or turbocharger seal problem
- Do not turn on the ignition or start the engine with the sensor port open
- If the codes remain after replacement, take the car to a repair shop for diagnosis