← Ranger Ford Ranger repair manuals →

Ford Ranger 2.2 TDCi 150 hp (2013): Glow Plug Replacement

The glow plugs on the 2.2 TDCi make cold starting easier. When they wear out, the engine is hard to start, emits white smoke, and the glow plug (coil) light comes on the dash. Before replacing them, check each plug with a multimeter, but replace all four at the same time. On this engine family, access to the glow plugs is gained by removing the air ducts and, as a rule, the intake manifold.

DifficultyMedium Time1.5-3 hours Steps25

Parts

2
№PartAlternatives
01 Glow plugs, 11 V, pencil-type (Ford 2.2 TDCi Duratorq)4 pcs, all of the same typeFind on Amazon → AlternativesBoschNGKBeruChampion
02 Intake manifold gasket setif the manifold is removedFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 9 more. See manuals →

Step by step

25 steps · 6 stages
Stage 1 of 6 Diagnosis and preparation 5 steps
  1. Make sure the engine is cold. Read the fault codes with an OBD scanner to rule out other causes of hard starting (injectors, fuel pressure, battery).
  2. Park the vehicle on level ground and set the parking brake.
  3. Disconnect the negative battery terminal. Wait a few minutes.
  4. Remove the engine cover and the air duct running from the air filter housing to the turbocharger to get access to the intake manifold.
  5. Thoroughly clean the manifold and the area around the glow plugs with compressed air and a rag: no dirt should get into the cylinders.
Stage 2 of 6 Accessing the glow plugs 4 steps
  1. Disconnect the sensor connectors and vacuum hoses on the manifold, and mark their positions.
  2. Remove the intake manifold. Unbolt the manifold fasteners and take it off together with the gaskets or seal rings.
  3. Cover the open intake ports in the cylinder head with clean plugs or rags.
  4. Disconnect the glow plug connector or power bus bar, and note the order in which it is connected.
Stage 3 of 6 Removing the old glow plugs 4 steps
  1. Remove the nuts or contact terminals from the glow plug terminals. Be careful not to break the terminals.
  2. Blow out the glow plug wells with compressed air.
  3. Unscrew each glow plug with the long 10 mm socket, keeping it straight without tilting. If a plug is stuck, apply penetrating oil, wait 15-20 minutes, then unscrew it with smooth movements, without applying sudden force.
  4. Inspect the threads in the cylinder head and the plugs themselves. If the tip has broken off in the head, stop and remove it with a special extractor, otherwise debris will fall into the cylinder.
Stage 4 of 6 Installing the new glow plugs 5 steps
  1. Compare the new plugs with the old ones for length and terminal shape.
  2. Lightly coat the threads with copper anti-seize grease, keeping it off the pencil tip. Thread each plug in by hand until it stops.
  3. Tighten the plugs with a torque wrench: according to factory data for the 2.2 Duratorq, the torque is about 10 N·m (7.4 lb-ft); for the Transit with the same engine, 13 N·m (9.6 lb-ft) is specified. Do not exceed 13 N·m (9.6 lb-ft), as the plug breaks easily.
  4. Fit the contact terminals and tighten the terminal nuts to a low torque (about 2 N·m (1.5 lb-ft) according to factory data for related engines). Do not overtighten.
  5. Connect the glow plug connector or power bus bar.
Stage 5 of 6 Reassembly 4 steps
  1. Remove the plugs from the ports. Install the intake manifold with new gaskets and tighten the fasteners evenly according to the manufacturer's specification.
  2. Reconnect the connectors and vacuum hoses according to the marks.
  3. Install the air duct and the engine cover.
  4. Reconnect the negative battery terminal.
Stage 6 of 6 Checking 3 steps
  1. Turn the ignition on, wait for the glow plug light to go out, and start the engine. It should start easily.
  2. Let the engine run for a few minutes and check for air leaks and fluid leaks at the manifold and ducts.
  3. Read the fault codes with the OBD scanner and clear them if necessary. Take a test drive.

Common mistakes and warnings

  • The main risk is breaking a glow plug off in the cylinder head during removal
  • Do not use force; if a plug seizes, use penetrating oil
  • Keep everything clean: any debris from the intake will get into the cylinders
  • If you have no experience, leave the job to a repair shop
  • The removal order and torque values for your vehicle may need to be verified for your specific vehicle
Spotted a mistake? Tell us →

Our articles

More articles →