← Aumark

Foton Aumark (1st generation): Replacing the Rear Axle Ring and Pinion Gear Set and Adjusting the Contact Pattern

The ring and pinion gear set is a pair of gears (the drive pinion and the ring gear) that transfers rotation from the driveshaft to the axle shafts. A new set is replaced only as a matched pair. Correct operation depends on four adjustments: pinion depth, pinion bearing preload, backlash, and differential bearing preload. The contact pattern shows whether the depth is set correctly. This job requires precise measurements and experience; without them, it is better to leave it to a repair shop. For the factory torque and clearance values for the Aumark rear axle, check the manufacturer's specifications. The general procedure is below.

DifficultyHard Time6-10 hours Steps18

Key figures

  • Contact pattern shift0.13-0.38 mm — change the shim thickness by this much on the first attempts until the pattern gets close to the target (step 14)
    large steps
  • Contact pattern shift0.05-0.10 mm — use steps this size to center the pattern between the tip and the root of the tooth (step 14)
    fine tuning
  • Shims and backlash relationshipa reference for adjusting backlash (step 11)
    0.25 mm of differential shift gives approximately 0.18 mm change in backlash
  • Cooling after the first driveotherwise the new gear set will overheat (step 18)
    30-40 minutes after the first 25-30 km
  • Gentle break-indrive this far without overloading or towing, then change the oil (step 18)
    800 km

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

7
№Part
01 Rear axle ring and pinion gear set (drive pinion and ring gear)matched set onlyFind on Amazon →
02 Pinion sealFind on Amazon →
03 Differential cover gasket or sealantFind on Amazon →
04 Hypoid gear oilFind on Amazon →
05 Pinion and differential bearingsif neededFind on Amazon →
06 Adjusting shimsif neededFind on Amazon →
07 Collapsible spacerif the design includes oneFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

11

Step by step

18 steps
  1. Park the vehicle on a level surface and secure it with wheel chocks. Lift the rear axle and place the vehicle on solid stands, then remove the rear wheels. Drain the oil from the rear axle.
  2. Disconnect the driveshaft from the pinion flange. First, mark the flange and the shaft with paint so you can reassemble them in the same position. Remove the brake drums or calipers and pull out the axle shafts (together with the hubs or separately, depending on your axle design).
  3. Remove the differential cover. Before disassembly, mark the position of the differential bearing caps with paint, along with their side (left and right), so they go back in their original places. Measure and record the original backlash as a reference.
  4. Remove the differential assembly. Do not mix up the shims and bearing races from side to side: if they are adjustable, record their thickness and position.
  5. Unscrew the pinion nut (holding the flange to keep it from turning), remove the flange, and press out the drive pinion. Remove the seal and discard the old one. Record the position and thickness of the adjusting shims or the condition of the collapsible spacer.
  6. Unbolt the ring gear from the differential case (bolts around the circumference). Inspect the bearings, races, and seats: wear or scoring can be fixed only by replacement. Thoroughly clean the housing and flush the oil passages with solvent; there must be no metal shavings in the housing.
  7. Clean the ring gear mounting surface on the differential case and remove burrs with a small file or a fine stone. Install the new ring gear on the case and tighten the bolts evenly in a crisscross pattern with a torque wrench (torque per Foton specifications), and apply threadlocker to the bolts.
  8. Preparing for assembly: press the rear bearing onto the new drive pinion and press the bearing races into the housing evenly, all the way in. For the first attempt, use depth shims of the same thickness as the ones installed before (the new set has a deviation marking on the end of the gear; if there is no marking, start with the previous thickness).
  9. Install the drive pinion, the front bearing, the new seal (lubricate the lip and the seat), and the flange. Tighten the pinion nut gradually, checking the pinion rotating torque with a low-range torque wrench. If the axle has a collapsible spacer, always install a new one and crush it very slowly: if you exceed the allowed preload, the spacer must be replaced with a new one and you must start over. If the preload is too low, tighten the nut further (or remove some shims); if it is too high, disassemble and add shim thickness. The allowable pinion bearing preload is given in the Foton specifications. After reaching the required value, seat the bearings by lightly tapping the ends of the pinion and check the preload again.
  10. Install the differential in the housing together with the bearings and adjusting shims or adjusting nuts. Install the bearing caps according to the marks and tighten them (torque per Foton specifications). The differential bearings should fit with a slight preload: no play, but not so tight that they can't be turned without effort.
  11. Check the backlash. Mount the dial indicator on the housing with the tip perpendicular to the ring gear tooth, hold the pinion flange so it does not turn, and rock the ring gear. Take the backlash value from the Foton specifications. A reference for adjustment: shifting the differential by 0.25 mm changes the backlash by approximately 0.18 mm. To reduce backlash, move the ring gear closer to the pinion axis; to increase it, move it farther away. When adjusting with shims, remove a shim from one side and add an identical one on the other, keeping the bearing preload; with adjusting nuts, tighten both evenly, and make the final tightening on the nut on the side the ring gear is pushed toward under load.
  12. Check the contact pattern (only after the backlash is within tolerance). Apply marking compound to 3-4 teeth of the ring gear in two places, then rotate the ring gear past the pinion several times forward and back (light braking of the ring gear gives a clear imprint). Examine the pattern on the drive side and the reverse ("coast") side of the teeth.
  13. Read the pattern as follows. The pinion depth is determined by the position of the pattern between the top (tip) and the root of the tooth. Pattern at the tooth tip: the pinion is too far from the ring gear — move it closer to the ring gear axis (add shims for a design with shims at the rear bearing; on a design with a support, remove them). Pattern at the tooth root: the pinion is too close — move it away (remove shims; on a support design, add them). The pattern position along the tooth (heel and toe) depends on the backlash. A good pattern sits right between the tip and the root of the tooth, even if lengthwise it is shifted toward the heel or toe.
  14. Order of changing depth. First change the shim thickness in large steps, approximately 0.13-0.38 mm, until the pattern gets close to the target, then in small steps of 0.05-0.10 mm until it is centered. After each depth change, recheck the pinion bearing preload and the backlash. For a used set, go by the pattern on the reverse side of the tooth; for a new set, go by both.
  15. When the pattern is correct, recheck the backlash and bearing preload once more, tighten the pinion nut with threadlocker (torque per Foton specifications), and bend or secure the lock, if one is provided. Wash the marking compound off all gears.
  16. Install the differential cover with a new gasket or a thin layer of sealant (clean the mating surfaces). Tighten the bolts in a crisscross pattern, torque per Foton specifications. Don't forget the breather.
  17. Install the axle shafts, brake components, wheels, and driveshaft according to the marks. Tighten the wheel nuts per Foton specifications. Fill with quality hypoid gear oil up to the lower edge of the fill hole.
  18. Break-in of the new gear set: after the first 25-30 km, let the axle cool for 30-40 minutes. Drive gently for the first 800 km, without overloading or towing. After that distance, change the oil — it contains metal dust from the break-in of the new gear set.

Common mistakes and warnings

  • This job affects safety: an incorrectly assembled axle can seize while driving or fail, and a mistake in tightening the wheels and driveshaft is dangerous
  • If you have no experience setting up hypoid gear sets and lack the necessary measuring tools, leave the job to a specialized repair shop
  • Do not replace just one gear: the pinion and ring gear work only as a matched set
  • All tightening torques (ring gear bolts, bearing caps, pinion nut, wheels, differential cover), the backlash tolerance, and the pinion bearing preload are per the manufacturer's specifications for your axle
  • Do not work under a vehicle supported only by a jack
Spotted a mistake? Tell us →