Autopapyrus · Honda Insight 1.3 IMA (2012)
https://autopapyrus.com/catalog/honda/insight/guides/removing-the-fog-light-trim-panel-in-the-front-bumper/
https://autopapyrus.com/catalog/honda/insight/guides/removing-the-fog-light-trim-panel-in-the-front-bumper/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Honda Insight 1.3 IMA (2012): Removing the Fog Light Bezel in the Front Bumper
On the second-generation Insight, the fog light bezel (trim ring) is attached from inside the bumper. A bracket with self-tapping screws is connected to it, and it cannot be unscrewed from the outside. To get access, you have to remove the entire front bumper. This guide covers the left side, and the right side is the same. The service manual does not give torque specs for this hardware. Tighten the self-tapping screws and clips into the plastic only until snug, without force.
Key figures
- Number of bumper tabs16 (8 on each side). Pull the bumper forward carefully so you don't break them (step 7)
- Clips on the underside8. All must be removed before taking off the bumper (step 6)
- Grille clips7. Removed at the very start, before the bumper (step 4)
- Light mounting self-tapping screws3. Removed with a Phillips screwdriver (step 12)
- Battery terminal socket10 mm, for disconnecting the negative terminal (step 2)
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part |
|---|---|
| 01 | Honda Insight fog light bezelleft or rightFind on Amazon → |
| 02 | Plastic bumper retaining clip setspares; clips are single-use and break during removalFind on Amazon → |
| 03 | Bumper trim piece ("eyebrow") under headlightif needed; single-use, breaks during removalFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
21 steps · 5 stagesStage 1 of 5 Preparation 3 steps
- Park the car on a level surface, turn off the engine and open the hood. Make sure you have the radio anti-theft code, because the radio may ask for it after the battery is disconnected.
- Disconnect the negative terminal of the 12-volt battery (10 mm wrench). This is the regular battery in the engine bay. This job does not involve the hybrid high-voltage battery.
- Lay a blanket on the floor nearby. The removed bumper will go on it.
Stage 2 of 5 Removing the front bumper 6 steps
- Remove the upper radiator grille trim (the plastic strip above the grille). It is held by seven short clips. Pry each clip with the clip remover and pull it out.
- Remove the two screws at the edges of the bumper and pull out the upper bumper retaining clips that are visible from the engine bay side.
- From underneath, pull out eight clips (some short, some long) and remove four self-tapping screws with a Phillips screwdriver. One or two of the screws are on the underside of the bumper near the wheel wells.
- With a helper, carefully pull the bumper forward by the corners. It sits on 16 tabs (eight on each side). Pull without jerking, so you don't break the guides.
- When the bumper comes free, disconnect the two wiring connectors (the fog light wiring and the sensors/lighting, if equipped). Press the lock tab on the connector housing and separate the connector.
- Remove the bumper and lay it face down on the blanket.
Stage 3 of 5 Removing the light and bezel 6 steps
- Inspect the bumper from the inside. Around the light opening there is a bracket (frame) with three self-tapping screws that hold the light, and three more screws secure a separate bezel bracket.
- Disconnect the two-pin bulb connector from the light itself and free the wiring from the clips on the bracket.
- Remove the three self-tapping screws that hold the light to the bumper and take off the light together with the brackets.
- Remove the three self-tapping screws that hold the bezel bracket to the bumper and take off the bracket.
- Remove the light bezel from the front of the bumper. If it is held by tabs, release them with your fingers or a plastic remover, without scratching the paint.
- If needed, remove the narrow trim piece ("eyebrow") under the light. It is held by one tab and one hook. It is single-use and may break during removal.
Stage 4 of 5 Reassembly 4 steps
- Install the bezel, then the bezel bracket. First, start the three self-tapping screws loosely to align the bezel, then tighten them. Tighten without force, so you don't strip the threads in the plastic.
- Install the light, secure it with three self-tapping screws, connect the bulb connector and route the wiring into the bracket clips.
- With your helper, bring the bumper up to the car, connect the two wiring connectors and fit the bumper onto the tabs (all 16). Then install the screws, and fit the clips and self-tapping screws on the underside and the top.
- Install the upper grille trim on its seven clips, reconnect the negative battery terminal and, if needed, enter the radio code.
Stage 5 of 5 Check 2 steps
- Turn on the parking lights and fog lights, and check that both work.
- Check the gaps along the seam where the bumper meets the fenders and hood. They should be even, with no protruding corners.
Common mistakes and warnings
- Tighten all clips and self-tapping screws into plastic without much force, or you will strip the mounting points
- Do not touch the glass of the bulb with your fingers, because this shortens the life of the bulb
- If you have not worked with a bumper before, it is better to do this with a helper and use plastic pry tools
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Honda
The founder of the famous company, Japanese entrepreneur Soichiro Honda, was born in 1906 into the family of a poor…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →