← S-MX

Honda S-MX (RH1, 1998): Diagnosing and Repairing a Single Door's Central Locking Actuator

If one door won't lock with the button while the others work, the culprit is usually not the control unit or a fuse but that door's actuator. Its mechanism gets gummed up with dirt and old grease, the small motor dies, or a wire breaks in the flexible rubber boot between the body and the door. First check and lubricate, then remove the door panel and replace or repair the actuator. This guide covers a single door. The procedure is the same for the other doors.

DifficultyMedium Time1-3 hours Steps26

Key figures

  • Number of WD-40 applications
    up to three nights in a row. If one application wasn't enough, repeat it (steps 6-7)
  • Test time
    12 V to the actuator for 1-2 seconds. Use this to test the motor out of the car; reversing the polarity reverses the direction (step 15)

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

3
№PartAlternatives
01 Central locking actuator (lock assembly with electric motor), S-MX doorfor the affected doorFind on Amazon → AlternativesTokai RikaDiamondTyc
02 Plastic door panel clipsFind on Amazon →
03 Light machine oil for the mechanismFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

6

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

26 steps · 6 stages
Stage 1 of 6 Diagnosis 4 steps
  1. Make sure that only one door is faulty: lock and unlock the car with the button on the driver's door and with the key in the lock. Check different doors. If the same door fails to respond every time, look for the problem in that door.
  2. Listen at the problem door while pressing the button. A click or faint buzzing with no movement of the rod means the motor is alive and the mechanism is gummed up. Complete silence points to the motor, the wiring or the connector.
  3. Check how the mechanism moves by hand: pull the interior lock button and the door handle. A stiff, squeaky action means the mechanism is gummed up.
  4. Inspect the rubber boot between the door pillar and the door. Flex the wires inside it: they most often break right there from years of opening and closing the door.
Stage 2 of 6 Lubrication without removing the door panel 3 steps
  1. Open the door and find the service hole or screw on the door edge near the lock. If there is a screw, remove it.
  2. Insert the WD-40 straw and generously flood the lock mechanism. Press the central locking button several times so the fluid spreads, then flood it again.
  3. Wait a few hours (overnight is better) and test it. According to owners' experience, if needed the procedure is repeated three nights in a row. Do not use white lithium, silicone or Teflon grease inside: over time it thickens and the mechanism gums up again. If the lock works, you're done. If not, go to Phase 3.
Stage 3 of 6 Removing the door panel 6 steps
  1. Disconnect the negative battery terminal to avoid short circuits while working on the door wiring.
  2. Remove the caps and unscrew the door panel screws: usually these are screws in the armrest handle, under the caps and near the interior door handle. Check the number and locations on the door itself and take a photo before removal.
  3. Remove the window crank trim, or unplug the power window switch connector, if equipped.
  4. Pry around the edge with the trim tool and release the clips, starting from the bottom edge. Pull the panel upward to unhook it from the top edge.
  5. Disconnect the switch connectors and the interior handle rod. Remove the panel and set it aside.
  6. Carefully peel back the polyethylene film (moisture barrier) without tearing it. It will need to be stuck back on.
Stage 4 of 6 Checking the actuator in the door 4 steps
  1. Find the actuator on the door lock, near the door edge. Unplug its connector.
  2. Use a multimeter to check the motor resistance at the actuator terminals: infinity means the motor winding is open. To test it, apply 12 V from the battery or a test lamp to the motor for 1-2 seconds (reversing the polarity reverses the direction). If the rod moves but stiffly, the mechanism is gummed up. Lubricate it.
  3. Check for power at the door connector on the body side: when the button is pressed, 12 V should appear briefly on the terminals. If there is no voltage, the fault is the wire in the boot or the control unit relay.
  4. If there is no voltage, test the wire for continuity from the door to the body, find the break (most often in the boot) and repair it by soldering with heat-shrink tubing.
Stage 5 of 6 Replacing or repairing the actuator 5 steps
  1. Disconnect the lock rods from the actuator: release the plastic rod clips and remember the position of each rod.
  2. Remove the lock mounting screws on the door edge and take out the lock assembly together with the actuator through the service opening in the door's inner panel.
  3. If the actuator is removable on its own, detach it from the lock. If the actuator is not serviceable separately and is part of the lock, replace the whole lock assembly. The sources give no tightening torques for this hardware, so tighten until snug without excessive force and check the exact value against the manufacturer's specifications.
  4. Optional, if only the motor is faulty: remove the motor cover and check the brushes and the bushing on the rotor shaft. A common failure is a bent or broken brush, and soldering or bending it back can bring the motor back to life.
  5. Install the new actuator or lock in reverse order, connect the rods and snap the clips into place.
Stage 6 of 6 Reassembly and testing 4 steps
  1. Before installing the door panel, plug in the connector and test the lock with the button and the key several times.
  2. Lubricate the lock rods and joints with light machine oil (not silicone).
  3. Stick the moisture barrier film back in place, hang the panel on the top edge, press in the clips, tighten the screws and connect the connectors.
  4. Reconnect the battery terminal and test locking and unlocking from the driver's door and with the key for several cycles.

Common mistakes and warnings

  • The door panel is held on by clips that break easily, so have a spare set on hand
  • Do not bend the wires in the door jamb boot sharply
  • If the doors have no airbags, there is no need to disable the SRS separately, but still disconnect the battery terminal
Spotted a mistake? Tell us →

Our articles

More articles →