← Elantra Hyundai Elantra repair manuals →

Hyundai Elantra (VI, AD): Front Door Window Regulator Motor Replacement

The gear motor on the front door is mounted on the window regulator mechanism inside the door and is reached after removing the door panel. Before replacing it, check the window switch and the fuse: if the window goes down and then stops, the cause may be worn motor brushes. There is no detailed factory step-by-step procedure for this model in publicly available sources. Door panel removal is described for the 2017-2020 Elantra, and the work on the motor itself follows the general principle.

DifficultyMedium Time1.5-2.5 hours per door Steps21

Key figures

  • Socket for the window motor fasteners
    7 mm (or Torx T20 bit). This tool removes and installs the gear motor (steps 14 and 16)
  • Socket for the speaker bolts
    8 mm. If the speaker is in the way, it is removed by its four bolts (step 11)
  • Number of door panel screws
    1. The only screw is hidden under the cover in the armrest (steps 3-4), and everything else is held by clips

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the cable bracket, tweeter connector and clips are on the trim

Back of the removed door trim as you see it1Bracket with cables2Black tab at the rear3Inner handle4White tweeter connector5Tweeter6Trim clipTap to enlarge
  1. 1Bracket with the inner handle and lock cables: take it off the trim, do not pull the cables out of it.
  2. 2Black plastic tab on the rear edge of the bracket: press it, lift the bracket and take it off the trim.
  3. 3Inner handle: a landmark, the cable bracket sits next to it.
  4. 4White tweeter connector: press the latch and pull the connector straight out.
  5. 5Tweeter: round speaker with a yellow cone, the white connector goes to it.
  6. 6Plastic trim clip: if it stayed in the door metal, pull it out with a clip remover and put it back into the trim.

Parts

3
№Part
01 Front door window regulator motor, 2017 Hyundai Elantra ADleft or right, depending on sideFind on Amazon →
02 Front door window regulator with motor, complete assemblyoption for high mileage, instead of the motor aloneFind on Amazon →
03 Plastic door panel retaining clipsget extras, some break during removalFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 5 more. See manuals →

Step by step

21 steps
  1. Lower the door window all the way, then turn the vehicle off. Disconnect the negative battery terminal. The door contains a side impact sensor, so wait a few minutes before reaching into the door.
  2. Open the door. Carefully pry off the black triangular trim piece in the upper inner corner of the door (where the mirror is) with the plastic trim tool and remove it.
  3. In the recess of the armrest handle, find the small notch on the rear edge of the plastic cover. Pry the cover off with a small flat-blade screwdriver.
  4. Remove the one Phillips screw under the cover. This is the only screw holding the door panel. Everything else is held by plastic clips.
  5. Insert the trim tool between the door metal and the panel plastic at the lower edge, starting from the notch at the front. Pull sharply toward you to release the clips. Work along the entire lower edge and both sides.
  6. Lift the panel upward to release it from the top edge of the door. Tilt the top toward you and hold the bottom with your knee or foot so you don't end up hanging on the wires.
  7. Disconnect the white tweeter connector: press the locking tab and pull the connector straight out.
  8. Remove the bracket with the inner handle and lock cables: press the black plastic tab on the rear edge, lift the bracket and remove it from the panel. Do not pull the cables out of the bracket.
  9. Disconnect the switch block connector: press the locking button and pull the connector out. Set the panel aside in a safe place.
  10. If any clips stayed in the door metal, remove them with a clip removal tool and push them back into the panel.
  11. Check the condition of the vapor barrier (waterproof sheet) on the door. Carefully peel it away from the metal without tearing it, because you will need it for reassembly. If the door module is secured and has a side impact sensor on it, do not drop or hit it.
  12. Move the window to the required height with the switch by temporarily connecting the connector, or secure it in the up position with masking tape over the top edge on the door frame. The window must not fall when you disconnect the motor.
  13. Disconnect the power connector from the gear motor.
  14. Remove the motor fasteners with a 7 mm socket (or a Torx T20 bit). The motor on the previous-generation Elantra is listed as having three bolts. Check the number and location of fasteners on the AD visually and remove all of them.
  15. Remove the old motor. If the teeth or the worm gear are damaged and the cable is torn, replace the complete mechanism assembly. Inspect the working part of the mechanism for a broken cable.
  16. Install the new gear motor and tighten the fasteners without overtightening. Check the exact torque value against the manufacturer's specifications. As a rough guide, for small 7 mm bolts it is a few N·m, meaning the effort of an ordinary ratchet applied by hand without jerking.
  17. Connect the motor connector and the switch block connector. Temporarily reconnect the battery. Check raising and lowering the window through its full travel several times before installing the panel.
  18. If the auto up/auto down mode does not work, perform an initialization after the check: run the window all the way down, then all the way up, and hold the switch for a few seconds. The exact initialization procedure for the AD is not described in publicly available sources, so check it against the manufacturer's specifications.
  19. Install the panel: hook the top edge, connect the switch and tweeter connectors, and set the cable bracket back in place until it clicks (front edge first, then the rear).
  20. Align the clips with the holes in the door and press them in evenly along the lower edge and the sides. Replace any broken clips with new ones.
  21. Install the trim piece in the door corner, thread in the single screw in the armrest and close the cover. Reconnect the battery, close the door, and check the handle, lock, window switches, central locking and speakers.

Common mistakes and warnings

  • The door has a side impact airbag sensor installed
  • Do not drop or hit it, and work with the battery disconnected
  • If you have no experience working near airbag systems, it is better to leave the replacement to a repair shop
  • Do not touch the window with your hand until it is secured: when the motor is disconnected, it drops down inside the door
  • Do not overtighten the motor fasteners, or you can strip the threads or damage the gearbox housing
Spotted a mistake? Tell us →

Our articles

More articles →