← H1 Hyundai H1 repair manuals →

Hyundai H-1 2.5 CRDi D4CB (2008): Engine Removal and Installation

The D4CB 2.5 CRDi in the H-1 can be removed together with the transmission or separately, after the accessories are taken off. Based on the documentation for this engine in Hyundai/Kia vehicles, the sequence is the same: drain the fluids, remove everything that is in the way or ties the engine to the body, separate the transmission, then lift the engine out with a hoist. The H-1 layout (engine under the seats and the front of the body) differs from other vehicles with this engine, so some of the access steps may differ. The torque values below are approximate, so check exact values against the manufacturer's service manual.

DifficultyHard Time1-2 days for an experienced mechanicremoval, installation and checks Steps14

Key figures

  • Engine mount tightening torque
    69-88 N·m (51-65 lb-ft). Set this on the torque wrench when installing the engine on its mounts (step 11). Too loose causes vibration, and too tight can strip or damage the fasteners.

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

6
№Part
01 Engine oilFind on Amazon →
02 Oil filterFind on Amazon →
03 CoolantFind on Amazon →
04 Gaskets and O-rings for removed hoses and linesFind on Amazon →
05 Crankshaft sealif neededFind on Amazon →
06 Clutch kitif needed, for manual transmissionFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

14 steps
  1. Park the vehicle on a level surface or a lift and chock the wheels. Disconnect the negative battery terminal, then the positive one. Remove the battery.
  2. Drain the engine oil and the coolant into clean containers. The coolant can be reused if it is clean.
  3. Remove everything that blocks access to the engine: the skid plate, the air filter with its ducts, the intercooler and turbocharger pipes, and the plastic engine covers. Plug open intake and fuel ports with caps or clean plastic film so no dirt gets in.
  4. Remove the radiator, the fan with its shroud, and the drive belt. Disconnect the heater hoses and the engine coolant hoses.
  5. The Common Rail fuel system works under high pressure. Before disconnecting any fuel lines, shut the engine off and let it sit. Never loosen the high-pressure lines on a running or recently stopped engine. Disconnect the fuel supply and return lines and plug them right away.
  6. Disconnect the wiring harnesses from the engine: ECU, injectors, sensors, alternator, starter, glow plugs. Photograph or label every connector. Unbolt and remove the A/C compressor without opening the refrigerant circuit (do not release the refrigerant; hang the compressor from the body).
  7. Disconnect the exhaust system from the exhaust manifold or turbocharger. Disconnect the control cables and linkages (throttle, if equipped), the vacuum hoses and the power steering lines (the power steering pump can stay on the body, tied off to the side).
  8. Separate the transmission: remove the driveshaft from the flange, then disconnect the drive and the clutch (cables or hydraulics). Remove the starter. Support the transmission with a jack and remove the bolts of the bell housing (the transmission-to-engine attachment). Remove the transmission mount and the crossmember, and take the transmission out separately.
  9. Attach the chain or lifting bar to the factory lifting eyes on the cylinder head and take up slack with the hoist until it carries the weight. Remove the nuts and bolts of the engine mounts.
  10. Slowly lift the engine, constantly checking that it does not catch on harnesses, lines or the body. Lift the engine out of the engine bay and set it on a stand or secure stands.
  11. Installation is the reverse of removal. Lower the engine with the hoist onto the mounts. Tighten the engine mounts to 69-88 N·m (51-65 lb-ft) (a reference value for the D4CB engine; check it against the manual for the H-1). Tighten all other fasteners to the manufacturer's specifications.
  12. When installing the transmission, apply a thin layer of high-temperature grease to the input shaft splines and make sure the transmission seats on the dowel pins without force. Do not use the bolts to pull the transmission against the engine.
  13. Reconnect all connectors, fuel lines, hoses, the radiator and the drive belt. Fill with oil and coolant and install the battery.
  14. Prime the fuel system as specified in the service manual (with the hand primer, if one is fitted). Start the engine and let it warm up. Check for oil, coolant and fuel leaks, warning lights on the instrument cluster, and clutch operation. Bleed the cooling system to remove air and top up the coolant.

Common mistakes and warnings

  • This job is difficult and dangerous: it involves a heavy engine on a hoist, a high-pressure fuel system and the air conditioning
  • Do not stand under a suspended engine and do not work without secure supports
  • If you lack experience, leave removal and installation to a repair shop
  • Open the Common Rail high-pressure lines and the A/C circuit only when necessary, and keep everything clean
  • Torque values other than the engine mounts are approximate, so check exact values against the manufacturer's service manual
Spotted a mistake? Tell us →

Our articles

More articles →