← Santa Fe Hyundai Santa Fe repair manuals →

Hyundai Santa Fe (TM, 2023): Rear Turn Signal Bulb Replacement

The Santa Fe TM has two versions of the rear turn signal: with a conventional bulb and with LEDs (on some trims). You can replace the bulb yourself. If your lamp uses LEDs, they can't be replaced individually, and the whole taillight assembly must be replaced. Rear taillight bulbs are usually replaced on both sides at once, since they wear out at the same rate.

DifficultyEasy Time20-30 minutes Steps14

Part

№PartAlternatives
01 Rear turn signal bulb, single-contact, amber or amber-envelope2 pcs, left and right sidesFind on Amazon → AlternativesOsramPhilipsNarva

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

3
  • Phillips screwdriver Amazon →
  • plastic trim removal tools (or a wide flat-blade screwdriver wrapped with tape) Amazon →
  • gloves or a clean cloth Amazon →
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 6 more. See manuals →

Step by step

14 steps · 4 stages
Stage 1 of 4 Preparation 4 steps
  1. Park the vehicle on level ground, turn off the engine, set the parking brake, and wait for the bulbs to cool down.
  2. Identify which side has the faulty turn signal. Turn on the hazard lights and inspect the rear lights. A frequent or very fast flashing rate on the instrument cluster also indicates a burned-out bulb.
  3. Open the tailgate. Inspect the taillight from the inside. If the turn signal is made up of LEDs rather than a bulb with a socket, the bulb can't be replaced. Contact a dealer or repair shop.
  4. Disconnect the negative battery terminal, as recommended by the manufacturer. Keep in mind that the clock and onboard electronics settings may reset afterward.
Stage 2 of 4 Accessing the socket 3 steps
  1. Loosen the retaining clips under the rear bumper and the screws on the wheel well liner on the side of the faulty bulb.
  2. Carefully pull the liner under the bumper back toward the vehicle to gain access to the back of the taillight. The plastic clips are brittle, so use the trim tool without jerking.
  3. Find the turn signal bulb socket on the back of the taillight. Check it against the bulb that isn't working: the lamp has several sockets (brake light, parking light, reverse light).
Stage 3 of 4 Replacing the bulb 3 steps
  1. Disconnect the connector if it is in the way, and turn the socket counterclockwise until its tabs line up with the slots in the taillight housing. Remove the socket from the taillight.
  2. Remove the old bulb by pulling it straight out of the socket, without tilting it. Inspect the socket and contacts. Clean off any soot or oxidation and, if necessary, apply a thin layer of dielectric grease.
  3. Insert the new bulb into the socket all the way. Don't touch the glass with bare hands: hold the bulb with a clean cloth or glove. Oily fingerprints on the glass shorten the bulb's life.
Stage 4 of 4 Reassembly and check 4 steps
  1. Insert the socket into the taillight and turn it clockwise until it locks. Reconnect the connector if you disconnected it.
  2. Reconnect the negative battery terminal (if you removed it) and turn on the hazard lights. Make sure the turn signal flashes evenly and at the same rate as the one on the other side.
  3. Reinstall the liner under the bumper and the wheel well liner, secure the clips, and tighten the screws.
  4. Check the turn signals (left and right) and the hazard lights again. If the lamp is fogged up or there is water inside, find the cause of the poor seal at the gasket.

Common mistakes and warnings

  • Don't touch the glass with bare hands
  • An oily residue can cause the bulb to overheat and burst
  • Wear safety glasses and work only with a cooled bulb
  • Replace a damaged or cracked bulb immediately and dispose of it carefully
  • If the turn signal uses LEDs, don't open the lamp yourself
  • Contact a dealer or repair shop
  • No tightening torque is needed for this job: the trim fasteners are only snugged down without force, so don't overtighten the screws
Spotted a mistake? Tell us →

Our articles

More articles →