Autopapyrus · Hyundai Starex (H-1, 2nd generation)
https://autopapyrus.com/catalog/hyundai/starex/guides/front-subframe-front-suspension-crossmember-replacement/
https://autopapyrus.com/catalog/hyundai/starex/guides/front-subframe-front-suspension-crossmember-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Hyundai Starex (H-1, 2nd generation): Front Subframe (Front Suspension Crossmember) Replacement
The Starex subframe carries the lower control arms, the steering rack and part of the engine mounts. Replacement is needed after impact deformation, corrosion or failure of the subframe mounts. The job requires lifting the vehicle and supporting the subframe with a jack. Torque values are approximate, so check the exact values against the manufacturer's service manual.
Key figures
- Subframe bolt torqueapproximately 80-100 N·m (59-74 lb-ft). Per the procedure, tighten in a crisscross pattern in step 9, and confirm the value against the manufacturer's service manual.
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the subframe mount cushion, bushing and nut are
Tap to enlarge
- 1Nut (self-locking, with a locking insert): fit a new one, do not reuse the old one.
- 2Subframe mount cushion: inspect it; replace it if cracked or destroyed.
- 3Cushion bushing: the bolt that holds the subframe to the body passes through it.
- 4Mounting area on the body (zone around the cushion): check for cracks, corrosion and deformation; mark the bolts with a marker or paint before disassembly.
Parts
5| № | Part | Genuine part no. | Alternatives |
|---|---|---|---|
| 01 | Front suspension subframe (crossmember) assemblyor separate bushings and mountsFind on Amazon → | ||
| 02 | Front suspension subframe bushingsif worn and the subframe is not replaced as an assemblyFind on Amazon → | 54584-B2000 | AlternativesFebestSKV |
| 03 | Subframe mountsif worn and the subframe is not replaced as an assemblyFind on Amazon → | 54584-B2000 | AlternativesFebestSKV |
| 04 | Self-locking subframe mounting nutsnew, if the originals were locking typeFind on Amazon → | ||
| 05 | Subframe mounting boltsnew, if the originals were locking typeFind on Amazon → | 54519-2E000 |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
8
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
12 steps- Park the vehicle on a level surface, chock the rear wheels and disconnect the negative battery terminal. Raise the front of the vehicle on a lift or jack stands and remove the front wheels.
- Remove the engine skid plate, if equipped. Mark the position of the subframe relative to the body (with a marker or paint around the bolts) so you can preserve the camber and toe settings later.
- Disconnect everything attached to the subframe: sway bar links, tie rod ends (use a puller), wiring harnesses, line retainers and sensors.
- Steering rack: remove its mounting bolts to the subframe or body and move the rack aside, tying it up with wire. Do not disconnect the power steering lines unless necessary. If you have to, place a container underneath and bleed the system after reassembly.
- Position a hydraulic jack or stand with a wide pad under the subframe and raise it slightly to take up the weight. If the engine rests on the subframe through a mount, support the engine from below or above.
- Unbolt the lower control arms from the subframe (or, if necessary, the ball joints from the steering knuckles) so the arms do not interfere with lowering. To keep the alignment, mark the position of the eccentric bolts, if fitted.
- While supporting the subframe with the jack, remove the mounting bolts to the body one at a time (usually 2-3 on each side). Slowly lower the subframe and pull it out from under the vehicle.
- Inspect the mounting points on the body for cracks, corrosion and deformation. Transfer the bushings, brackets and any separately supplied parts to the new subframe. Compare the dimensions and hole positions with the old one.
- Installation: raise the subframe with the jack, align it with your marks, insert all the mounting bolts and snug them by hand. Then tighten them fully in a crisscross pattern. The typical range for subframe-to-body bolts on similar Hyundai vehicles is 80-100 N·m (59-74 lb-ft), but take the exact value from the manufacturer's service manual.
- Install the control arms, sway bar links, steering rack and tie rod ends with new self-locking nuts. Fully tighten the control arm bolts only after the vehicle is lowered onto its wheels (suspension under load), otherwise the bushings will wear out quickly. Torque values per the service manual.
- Install the skid plate and wheels, tighten the lug nuts to specification and lower the vehicle. If you disconnected the power steering lines, top up the fluid and bleed the system.
- Be sure to have the wheel alignment (camber and toe) done on an alignment rack. Then check the steering with a short test drive.
Common mistakes and warnings
- The subframe carries the steering and suspension, so it is a safety-critical part
- If you lack experience or a lift with reliable supports, leave this job to a repair shop
- Never work under a vehicle supported only by a jack
- Replace old subframe fasteners with new ones if they are the locking type
- A wheel alignment is mandatory after replacement
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Hyundai
Hyundai Motor Company, whose name means "modernity" in Korean, is South Korea's largest automaker and one of the top…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →