← Terracan Hyundai Terracan repair manuals →

Terracan (1st generation, HP): Heater Fan Switch Connector Repair

Over time, the heater fan switch connector oxidizes and overheats, the plastic melts, and the fan works only on some speeds or doesn't turn on at all. The repair consists of inspecting the connector, replacing the damaged terminals or the whole connector housing, and checking the switch and the resistor.

DifficultyMedium Time1-2 hours Steps13

Key figures

  • Heater fan relay fuse
    30 A. Check it first in the interior fuse box under the dashboard on the left (step 2), before disassembling the console
  • Fan and A/C circuit fuse
    10 A. Second on the list to check in the same box (step 2)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the heater fan connectors are under the dash

View from below with the glovebox lowered1Connectors: white and black2Ribbed air duct3Metal beam4Lowered gloveboxHook-and-loop straps on the sides hold the gloveboxTap to enlarge
  1. 1Two connectors with wire bundles at the top of the housing: white and black. They are latched blocks: inspect them and unplug by pressing the latch.
  2. 2Ribbed black heater air duct housing with clips. The resistor block is inside the heater duct and is not visible in this photo.
  3. 3Metal beam with brackets at the ends: a landmark below the heater housing.
  4. 4Lowered glovebox: it is dropped down and opens access to the heater housing.

Parts

3
№Part
01 Heater fan switch mating connector with terminal set and pigtail wiresterminals for the required wire gaugeFind on Amazon →
02 Heater fan switch assemblyif the contacts are in poor conditionFind on Amazon →
03 Heater fan resistor (resistor block)if it is also overheatedFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online). See manuals →

Step by step

13 steps
  1. Park the car on a level surface, turn off the engine, disconnect the negative battery terminal, and wait a few minutes.
  2. Before disassembly, check the fan fuses in the interior fuse box under the dashboard on the left (in the left pillar behind a protective cover): the 30 A fan relay fuse (No. 7) and the 10 A fuse (No. 25, "Fan & A/C, ETACM, Heater Relay"). The numbering may differ from the diagram on the cover, so go by the cover.
  3. Remove the trim panel of the climate control unit, prying it at the edges with trim tools so you don't break the clips. If necessary, remove the center console trim frame; any screws can be removed with a Phillips screwdriver.
  4. Pull the heater control unit and switch out of the recess far enough to reach the back. Take a photo to record the connector positions and wire colors.
  5. Press the locking tab and carefully disconnect the connector from the switch without pulling on the wires.
  6. Inspect the connector and the switch pins: darkening, melted plastic, green corrosion, darkened terminals. If the plastic is deformed or the terminals are darkened, repair the connector instead of just cleaning it.
  7. If the damage is minor: clean the contacts with contact cleaner and fine sandpaper, slightly squeeze the terminal sockets' tabs together, and treat them with contact grease.
  8. If the connector is melted: remove the terminals from the old connector (lifting the retainer with a thin screwdriver), cut off the burnt sections of the wires back to clean copper, crimp or solder on new terminals, and insert them into the new connector following the photo. Insulate the solder joints with heat-shrink tubing. Do not leave burnt, darkened copper: it heats up more.
  9. Check the switch: connect a multimeter across the contacts in each position and make sure the resistance in the closed position is close to zero. If the switch contacts are burnt or the switch sticks, replace it as an assembly.
  10. Check the heater fan resistor (the resistor block in the heater air duct) and its connector. A common cause of connector overheating is a worn fan drawing excess current or a burnt-out resistor. If the fan turns stiffly, replace it as well, otherwise the new connector will melt again.
  11. Plug in the connector until it clicks, and secure the wiring so that it doesn't press against the housing and isn't stretched.
  12. Reconnect the negative terminal, turn on the ignition, and check all fan speeds. After 5-10 minutes of running at maximum speed, touch the connector (after switching the ignition off): it should be only slightly warm.
  13. Reinstall the control unit and trim panels.

Common mistakes and warnings

  • Work only with the battery disconnected: airbag circuits run near the panel, so don't damage their wiring and connectors
  • Severe connector heating means high contact resistance or an overloaded fan, which is a fire hazard
  • If the cause isn't found, don't run the heater at high speeds and take the car to a repair shop
  • No torque specification applies to this job: tighten the panel screws without force
Spotted a mistake? Tell us →

Our articles

More articles →