https://autopapyrus.com/catalog/hyundai/tucson/guides/computer-diagnostics-of-engine-electrical-systems/
Hyundai Tucson 2.0 CRDi 150 hp (2013): Computer Diagnostics of Engine Electrical Systems
The Tucson II (LM) diesel is a 2.0 CRDi turbodiesel with a common rail system, not a VW TDI. It is controlled by an engine control unit that stores fault codes for sensors, actuators and power supply circuits. Diagnostics consist of reading the codes, viewing live data and checking suspect circuits with a multimeter.
Parts
5| № | Part |
|---|---|
| 01 | Sensorsif faultyFind on Amazon → |
| 02 | Glow plugsif faultyFind on Amazon → |
| 03 | Injectorsif faultyFind on Amazon → |
| 04 | Relaysif faultyFind on Amazon → |
| 05 | Wiring harnessesif faultyFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more.
See manuals →
Step by step
11 steps- Check the starting condition. Shut off the engine and check the battery charge and terminals. Low voltage causes false sensor and module communication errors. If the Check Engine light is flashing, do not drive the vehicle. Call a tow truck.
- Locate the 16-pin OBD-II diagnostic connector. It is usually under the dashboard to the left of the steering column, near the driver's feet. If needed, use a flashlight and remove the lower trim panel.
- Connect the scanner with the ignition off. Turn the ignition on, but do not start the engine yet. Select Hyundai, Tucson/ix35 model, 2.0 CRDi diesel engine. A generic OBD scanner shows only generic engine codes, while a brand-specific scanner also shows codes from other modules.
- Read the engine fault codes. Write down each code and its status: permanent, stored or pending. Take a screenshot or photograph the screen. Do not clear any codes until you have recorded all of them.
- Read the freeze frame data for each code: engine speed, temperature, load and pressure at the moment the fault occurred. It shows the conditions under which the fault appeared.
- View the live data with the engine cold and with it warmed up. Compare the readings: coolant temperature, intake air temperature, mass airflow (MAF sensor), boost pressure, rail pressure (specified and actual), system voltage and accelerator pedal position. If the cold-engine temperatures from different sensors differ greatly, suspect a faulty sensor or wiring.
- Check the circuits the codes point to. Inspect the connectors and harnesses near the sensor for signs of oil, oxidation, chafed insulation and poor retention. Disconnect the connector, inspect the terminals, clean them with electrical contact cleaner and reconnect. Measure sensor resistance and voltage with a multimeter. Get the acceptable values for this engine from the manufacturer's service manual.
- Check the glow plugs and their relay if the codes or hard cold starting point to them. Use a multimeter to check for power at the relay and the continuity of each glow plug. Compare the glow plug resistance with the service manual.
- Check the ground wiring and the power supply to the control unit. Inspect the ground terminals on the body and engine. They should have no corrosion or loose nuts. Check the engine control unit fuses and relays in the engine compartment. If you had to unbolt a connector or ground, tighten the fasteners without overtightening. Use the torque value from the manufacturer's service manual.
- If the codes point to rail pressure, the injectors or the high-pressure pump, have any further checks on the common rail fuel system done only at a repair shop. The system operates at very high pressure and must not be disassembled at home.
- After fixing the cause, clear the codes, turn the ignition off for 10-15 seconds, start the engine and read the faults again. Take a 10-15 minute test drive under varying loads. Then check the fault memory once more. A code that returns means the cause has not been fixed.
Common mistakes and warnings
- Do not clear faults without recording them first, or you will lose information needed for diagnosis
- Do not replace parts at random based on a code alone
- A code points to a circuit or system, not necessarily the sensor itself, and the wiring, connector or power supply is often to blame
- Leave work on the high-pressure fuel system and the coding of new injectors or a new control unit to a specialist shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Hyundai
Hyundai Motor Company, whose name means "modernity" in Korean, is South Korea's largest automaker and one of the top…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →