Autopapyrus · Hyundai Tucson 2.0 / 2.7 (2006)
https://autopapyrus.com/catalog/hyundai/tucson/guides/master-cylinder-replacement/
https://autopapyrus.com/catalog/hyundai/tucson/guides/master-cylinder-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Hyundai Tucson 2.0 / 2.7 (2006): Brake Master Cylinder Replacement
The master cylinder is mounted on the brake booster in the engine compartment on the driver's side. The air filter housing must be removed for access. The whole brake system must be bled after replacement. This guide covers replacing the complete cylinder; rebuilding it with new seals is not recommended on this model.
Diagram: where the master cylinder is and what holds it
Tap to enlarge
- 1Master cylinder: metal body on the booster. It is replaced as a whole.
- 2Reservoir sits right on the cylinder. Remove the cap and pump the fluid out with a syringe.
- 3Two fittings under the reservoir: brake lines are screwed onto them. Undo with a flare-nut wrench and plug the line ends.
- 4Two nuts with washers on the booster studs hold the cylinder flange. Remove them and pull the cylinder straight off.
- 5Fluid level sensor connector on the reservoir: disconnect it first.
- 6Brake vacuum booster: black drum at the bulkhead. The cylinder comes off it.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Brake master cylinder assembly for Hyundai Tucson JMversion with or without ABS; 2.0 or 2.7 engineFind on Amazon → | AlternativesATETRWFebiBosch |
| 02 | DOT 4 brake fluidabout 1 L (1.06 qt) for topping up and bleedingFind on Amazon → | |
| 03 | Brake fluid reservoir sealif sold separatelyFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- Flare nut (line) wrench set Amazon →
- 10 mm and 11 mm (closed-end profile preferred) Amazon →
- ratchet with sockets for the cylinder mounting nuts and air filter housing bolts Amazon →
- torque wrench Amazon →
- syringe or bulb for removing fluid Amazon →
- bleeder hose and clear container Amazon →
- plugs or clean cloth Amazon →
- shop rags Amazon →
- helper Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more.
See manuals →
Step by step
25 steps · 5 stagesStage 1 of 5 Preparation 4 steps
- Park the vehicle on level ground, shut off the engine and let it cool. With the engine off, press the brake pedal 5-6 times to deplete the vacuum in the booster.
- Lay rags around the cylinder and over the fender: brake fluid damages paint. Have the new DOT 4 fluid ready.
- Loosen the air filter housing bolts and lift the housing off its bracket together with any ducts that block access.
- Disconnect the brake fluid level sensor connector on the reservoir.
Stage 2 of 5 Removal 6 steps
- Remove the reservoir cap and draw as much fluid out of the reservoir as possible with a syringe. Pour the old fluid into a separate container.
- Label or remember which line goes to which port. Mark them with a marker on a rag or take a photo.
- Use a flare nut wrench to loosen the fittings of the two brake lines on the cylinder. Do not use an adjustable wrench: it can easily round off the flats.
- Move the lines aside and immediately plug their ends or cover them with clean cloth to stop fluid from leaking out and keep dirt out.
- Remove the two nuts with washers that hold the cylinder to the brake booster.
- Pull the cylinder straight toward you along its axis, without tilting it, and take it off the booster. Watch the booster pushrod and the seal ring on the end face.
Stage 3 of 5 Installation 5 steps
- Wipe the booster mounting surface. Compare the old and new cylinders: the ports, reservoir, sensor connector and pushrod length must match.
- If the new cylinder has no reservoir or cap, transfer them from the old one. Install the reservoir seal on it.
- Slide the new cylinder onto the booster studs without tilting it. Thread on the nuts with washers and tighten them evenly in a crisscross pattern. Approximate torque: 8-12 N·m (6-9 lb-ft); check the exact value in the manufacturer's specifications.
- Thread the brake lines into the ports by hand first to avoid cross-threading, then tighten with the wrench. Approximate torque: 13-17 N·m (10-13 lb-ft); check the exact value in the manufacturer's specifications.
- Connect the fluid level sensor connector.
Stage 4 of 5 Filling and bleeding 6 steps
- Fill the reservoir with fresh DOT 4 fluid up to the MAX mark.
- Attach the hose to the bleeder valve of the wheel farthest from the cylinder (usually the rear right) and put the other end in a container with a small amount of fluid.
- Have your helper slowly press the brake pedal several times and hold it down, without pushing it all the way to the floor. While the pedal is held, open the bleeder valve, wait for air and fluid to come out, and close the valve before the helper releases the pedal.
- Repeat until fluid comes out of the hose without bubbles. Keep topping up the reservoir so the level never drops below minimum.
- Bleed the remaining wheels the same way: front left, then rear left and front right (order from farthest to nearest). On vehicles with ABS, if air remains in the unit, additional bleeding with diagnostic equipment at a repair shop may be needed.
- Install the air filter housing, tighten its fasteners and reconnect the ducts.
Stage 5 of 5 Check 4 steps
- Start the engine. The pedal should feel firm and should not sink or slowly drop under steady pressure.
- Inspect the line connections and cylinder mounting for leaks, check the fluid level in the reservoir and top up if needed.
- Make sure the brake warning light on the instrument panel is off.
- Drive at low speed in a safe area and test the brakes several times. Only after that return to normal driving.
Common mistakes and warnings
- The brake system is a safety-critical system
- If you have no experience working on brakes, have the replacement and bleeding done by a repair shop
- Do not drive the vehicle with a soft or sinking pedal
- Brake fluid damages paint and irritates skin; wash it off immediately with plenty of water
- The torque values in the text are approximate
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Hyundai
Hyundai Motor Company, whose name means "modernity" in Korean, is South Korea's largest automaker and one of the top…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →