Isuzu Rodeo — repair and maintenance
2 step-by-step guides
Isuzu Rodeo guides
143Engine25
- Diagnosing engine failures and loss of engine performance
- Replacing the rear crankshaft oil seal
- Replacing the valve springs, spring retainers and valve stem oil seals
- Replacing the engine mounts
- Replacing the front crankshaft oil seal
- Checking the compression pressure
- Checking the condition of and replacing the engine mounts
- Checking the condition of the crankshaft
17 more
- Checking the condition of the connecting rod and piston assembly components
- Engine repair
- Assembling the cylinder head
- Removing and installing the cylinder head
- Removing and installing the cylinder heads
- Removing and installing the torsional vibration damper
- Removing and installing the timing chain cover
- Removing and installing the oil pump
- Removing and installing the flywheel/driveplate
- Removing and installing the oil pan
- Removing and installing the A/C receiver/drier
- Removing and installing the rocker arm and camshaft assembly
- Removing the crankshaft
- Removing the piston and connecting rod assemblies
- Removing, inspecting and installing the camshafts
- Removing, installing and adjusting the timing belt tension
- Installing the piston rings
Suspension & steering19
- Diagnosing rear suspension faults
- Diagnosing faults of steering and suspension components
- Diagnosing front suspension faults
- Rear suspension
- Replacing the leaf springs
- Replacing the torsion bars
- Bleeding the power steering hydraulic system
- Adjusting the steering wheel free play.139
11 more
- Front suspension repair
- Removing and installing the shock absorbers
- Removing and installing the upper suspension control arm
- Removing and installing the rear shock absorbers
- Removing and installing the steering knuckle
- Removing and installing the steering wheel
- Removing and installing the steering gear
- Removing and installing the power steering pump
- Removing and installing the steering column
- Removing and installing the front axle assembly (4WD models)
- Removing and installing the anti-roll bar
Electrical20
- Replacing the lighting bulbs
- Checking the operation of and replacing the fuel flow sensor
- Checking the operation of and replacing the information sensors
- Checking the operation of and replacing the horn
- Checking the condition of and replacing the ignition coil
- Checking the operation of the ignition system
- Checking, adjusting and replacing the start inhibitor switch
- Adjusting the air gap
12 more
- Adjusting the headlight beam direction
- Repairing the ignition system
- Repairing the starting system
- Removing and installing the radio antenna
- Removing and installing the headlight assemblies
- Removing and installing the instrument cluster
- Removing and installing the A/C condenser
- Removing and installing the instrument panel
- Removing and installing the ignition distributor
- Removing and installing the door window regulators
- Removing and installing the instrument panel switch assembly
- Removing and installing the electronic control module (ECM)
Fuel system12
- Carburettor troubleshooting and overhaul
- Checking and replacing the fuel injection components
- Checking fuel pump operation and fuel pressure
- Checking the condition of and replacing the fuel lines and their fittings
- Carburettor adjustments
- Repairing the fuel system
- Releasing the fuel system pressure
- Removing and installing the carburetor
Brakes9
Transmission27
- Diagnosing faults of driveline components
- Diagnosing transfer case faults
- Troubleshooting the clutch
- Diagnosing the automated manual transmission
- Replacing the universal joints
- Replacing the differential drive pinion oil seal
- Replacing the clutch
- Replacing the center bearing
19 more
- Servicing the automatic transmission
- Checking and adjusting the gearshift linkage
- Checking the condition of the driveshaft CV joints and replacing their protective boots
- Checking the condition of and replacing the transmission mount
- Inspecting the condition of the clutch components
- Inspecting the condition of the driveline components
- Bleeding the hydraulic clutch actuator
- Adjusting the kick-down cable (TV cable)
- Repairing the transfer case
- Removing and installing the automatic transmission
- Removing and installing the rear axle shaft, bearing and oil seal
- Removing and installing the propeller shafts
- Removing and installing the front driveshafts (4WD models)
- Removing and installing the transfer case
- Removing and installing the shift control lever
- Removing and installing the rear axle assembly
- Removing, overhauling and installing the clutch master cylinder
- Removing, inspecting and installing the clutch assembly components
- Removing, installing and adjusting the clutch cable
Cooling system12
- Diagnosing engine cooling system faults
- Replacing the condenser fan
- Replacing the water pump
- Servicing the engine cooling system
- Checking the operation of and replacing the thermostat
- Checking the condition of the water pump
- Removing and installing the intake manifold
- Removing and installing the radiator grille trim
Exhaust system3
Body & glass9
- Replacing the windshield and other fixed glass
- Checking the operation of the instrument panel gauges
- Removing and installing the bumpers
- Removing and installing the windscreen wiper motor
- Removing and installing the exterior rear-view mirrors
- Removing and installing the instrument panel trim
- Removing and installing the front wings
- Removing, installing and adjusting the tailgate
Need a job that isn't listed? Pick your engine, year and the job, and we'll build a step-by-step guide for your car in a few minutes.
Build a guide →Need a part? Search Amazon for Isuzu Rodeo parts: filters, brakes, sensors, belts. Check the fit for your year and engine before you buy.
Find parts on Amazon →How well do you know the Isuzu Rodeo? Ten questions on its history, engines and records, with the answer explained after each pick.
Take the quiz →