https://autopapyrus.com/catalog/kia/carnival/guides/rear-window-defroster-diagnosis-and-repair-grid-lines-relay-fuse/
Rear Window Defroster Diagnosis and Repair (Grid Lines, Relay, Fuse)
The rear window defroster on the Kia Carnival III (UN) consists of grid lines fused into the glass, a button on the climate control panel, a relay and a fuse. The defroster works only while the engine is running and shuts off by itself after about 20 minutes. Check the fuse and relay first, then the power at the glass, and only then repair the grid lines.
Key figures
- Defroster auto shut-offafter this time the defroster turns off by itself; this is normal, not a malfunction (step 1)about 20 minutes
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the rear window heating lines are and how to repair a break
- 1Heating line fused into the glass. Inspect it from inside for scratches, wear and breaks.
- 2Marker mark at the break. Mark the damage with a marker on the outside of the glass.
- 3Tape. Tape both edges of the line 1-2 mm wider than the gap so the repair line is even.
- 4Conductive glue or varnish on the line ends. Apply a continuous layer into the gap, overlap both ends of the broken line and let it dry.
- 5Glass terminal with wire. Good contact is a must: solder a detached terminal back or glue it with conductive glue.
Parts
4| № | Part |
|---|---|
| 01 | Rear defroster fuseFind on Amazon → |
| 02 | Rear defroster relay (4-pin)Find on Amazon → |
| 03 | Conductive adhesive repair kit for defroster grid linesFind on Amazon → |
| 04 | Heated rear window glass assemblyonly if most of the grid lines are damagedFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 4 more.
See manuals →
Step by step
12 steps- Make sure the engine is running: the defroster works only with the engine on. Press the defroster button on the climate control panel. The indicator on the button should light up. If the indicator does not light up, the cause is the button, the fuse or the relay. If it lights up but the glass does not heat, look for a break in the grid lines or at the glass terminals.
- Inspect the grid lines on the inside of the glass. Look for scratches, scuffs and breaks. The lines often break where items rest against the glass or where cargo straps rub. Wipe the glass with a soft cloth.
- Find the fuse box using the diagram on its cover. The rear defroster fuse is listed there as well. Remove it with a fuse puller and hold it up to the light. Replace a blown fuse with one of the same rating. Never install a higher-rated fuse.
- If the fuse blows again, there is a short circuit in the circuit. The cause may be damaged wiring in the left or right tailgate pillar or in the tailgate hinge. Do not keep replacing the fuse; find the short instead.
- Check the relay. Disconnect the negative battery terminal. Find the relay in the box using the diagram on the cover. Apply 12 V from the battery to the coil terminals (85 and 86). Continuity should appear between the power terminals 30 and 87. With power removed, there should be no continuity. If the relay does not click or does not conduct, replace it with a new one.
- Check the power at the glass. Reconnect the negative battery terminal. Start the engine and turn on the defroster. With a multimeter set to DC voltage, measure the voltage across the two terminals at the edges of the glass. It should be close to the vehicle system voltage (about 12-14 V). If there is no voltage, there is a break in the wiring between the relay and the terminals; check the wires and connectors. If voltage is present but the glass does not heat, the grid lines are damaged.
- Find the location of the break. Measure the voltage between one of the glass terminals and a probe touched to each grid line in turn at its midpoint. A good section reads about half of the voltage. At a break, the reading changes sharply to zero or to the full value. Mark the damage with a marker on the outside of the glass.
- Prepare the grid line for repair. Turn off the defroster and disconnect the battery. Wipe the area with rubbing alcohol. Tape off the two edges of the line 1-2 mm wider than the gap so the repair line comes out even.
- Apply the conductive adhesive or paint from the repair kit into the gap. Overlap both ends of the broken line. The layer must be continuous. Let it dry according to the kit instructions. Do not turn on the defroster until it is completely dry. Remove the tape.
- Reconnect the battery, start the engine and turn on the defroster. After a few minutes, run your hand over the repaired area; it should warm up the same as the neighboring lines. If not, repeat the repair or check the contact.
- If a terminal on the edge of the glass has come off, solder it back in place or glue it on with conductive adhesive. A good connection is essential, otherwise the terminal will overheat.
- If a large part of the grid lines is damaged, repair is not practical. In that case, replace the complete heated glass. This job is best done at a repair shop, because the glass is bonded in with sealant.
Common mistakes and warnings
- To avoid damaging the grid lines on the inside of the glass, never clean it with sharp objects or abrasive cleaners
- Conductive adhesive repair is suitable only for single breaks
- If you are inexperienced, have a repair shop handle work on the wiring in the tailgate and pillar so you don't damage the harnesses
- Check the exact fuse rating and the relay location against the diagram on the fuse box cover of your vehicle