← Ceed Kia Ceed repair manuals →

Kia Ceed (1st generation, ED): Parking Brake Adjustment

The parking brake lever should rise a small number of clicks, and the rear wheels should turn freely with the lever released. Adjustment is made with the nut on the cable under the lever, after the rear brakes have been checked for wear. If the lever travels too far and the nut is already adjusted all the way, the cable is stretched or the shoes are worn. In that case you need to replace parts, not adjust.

DifficultyEasy Time30-60 minutes Steps11

Diagram: where the parking brake adjusting nut is and how to reach it

View of the console between the front seats from abovecup holderclips along the edgehandle with buttonnut and lock nutcable goes rearward1Parking brake lever2Console trim panel: remove3Armrest box4Cable nut: turn it5Cable from lever to nutTap to enlarge
  1. 1Parking brake lever: pull it with moderate force and count the clicks.
  2. 2Console trim around the lever: if there are more clicks than normal, carefully remove it without breaking the clips.
  3. 3Armrest box: next to the lever, its recess under the lid gives access to the cable.
  4. 4Cable adjusting nut with its lock: turn it half a turn at a time and check the lever travel each time.
  5. 5Parking brake cable: runs from the lever to the nut and on toward the rear wheels.

Part

№Part
01 Not required. If adjustment does not help, check the parking brake cable and the rear brake shoes (the parking brake shoes inside the disc brake drum or the rear brake pads, depending on trim level)Find on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more. See manuals →

Step by step

11 steps
  1. Park the vehicle on a level surface and place chocks under the front wheels. The rear axle will be raised later.
  2. Before adjusting the cable, make sure the rear brakes are in good condition. If the rear brake system is worn or incorrectly adjusted, do not tighten the cable: it will bind and drag on the shoes.
  3. Before adjusting, press the brake pedal several times. On the factory procedure for a similar Kia model, this is done so the rear shoes settle into their working position.
  4. Check the lever travel. Pull it with moderate force (about 10 kg (22 lb)) and count the clicks. The approximate specification for Kia is 5-8 clicks. Verify the exact value for the Ceed against the manufacturer's specifications.
  5. If there are more clicks than specified, remove the center console trim around the parking brake lever (fasteners and clips vary, so work carefully to avoid breaking the clips).
  6. Under the lever, find the adjusting nut on the cable and its retainer (a clip or lock nut). Remove the retainer if there is one.
  7. Turn the nut: turning it in the tightening direction tensions the cable and reduces the number of clicks. Turn it in half-turn increments and check the lever travel each time. There is no specified tightening torque. Tighten only until you get the correct travel.
  8. Raise the rear axle with the jack onto jack stands, release the lever fully, and turn both rear wheels by hand. They should turn freely, with no shoe contact. If there is any rubbing, loosen the nut a quarter turn.
  9. Turn the ignition on and raise the lever one click: the parking brake indicator light on the instrument panel should come on. If it does not, check the switch under the lever.
  10. Reinstall the nut retainer, install the console trim, and lower the vehicle.
  11. Test the parking brake on a slight incline: the vehicle should hold securely when the lever is raised about 4-6 clicks.

Common mistakes and warnings

  • The parking brake is a safety component
  • If the vehicle does not hold well on an incline after adjustment, or the wheels rub with the lever released, do not drive the vehicle and take it to a repair shop
  • Do not overtighten the cable: the shoes will drag constantly, overheat, and wear out quickly
  • The click counts and force given above are approximate
  • Verify the exact values for the Ceed against the manufacturer's specifications
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →