Autopapyrus · Kia Forte (1st generation, TD)
https://autopapyrus.com/catalog/kia/forte/guides/brake-fluid-replacement-and-brake-bleeding/
https://autopapyrus.com/catalog/kia/forte/guides/brake-fluid-replacement-and-brake-bleeding/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Kia Forte (1st generation, TD): Brake Fluid Replacement and Brake Bleeding
Brake fluid absorbs moisture, which lowers its boiling point and causes corrosion in the calipers and ABS unit. The fluid is replaced by bleeding all four wheels completely. This is a safety-related job, so work carefully.
Key figures
- Fluid typefill the reservoir with it and use it for bleeding (steps 2-3); don't mix different typesDOT 4
- Reservoir levelotherwise air will get into the system (step 7)between MIN and MAX, and no lower than 3/4 during bleeding
- Bleeder screw torqueuse a torque wrench in step 8; don't overtighten, because the bleeder screw can break offabout 6-9 N·m (4.4-6.6 lb-ft)
- Bleeding orderstep 4right front, left front, right rear, left rear
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part |
|---|---|
| 01 | DOT 4 brake fluid (SAE J1704 DOT-4 LV, ISO 4925 Class 6, FMVSS 116 DOT-4)about 1 L (1.1 qt)Find on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8Step by step
14 steps- Park the vehicle on level ground, apply the parking brake, and chock the wheels that stay on the ground. Loosen the lug nuts, raise the vehicle, support it on jack stands, and remove the wheels.
- Wipe off the master cylinder reservoir cap so dirt doesn't get inside. Open the cap and draw the old fluid out with a syringe down to the bottom of the reservoir (don't leave it empty). Top up with fresh fluid between the MIN and MAX marks.
- Don't mix different types of fluid, and don't use fluid from a container that has been open for a long time. Keep fluid off the paint, because it eats away the finish.
- Bleeding order: right front, left front, right rear, left rear wheel. Sources disagree on the order, but one rule is common: start with the bleeder screw that is farthest from the master cylinder. If you know the correct order for your vehicle for certain, follow that.
- Remove the protective cap from the bleeder screw on the caliper and attach the clear hose, then put the other end into the clear container. To be safe, pour a little fresh fluid into the container so the end of the hose is submerged in it.
- Have your helper press the brake pedal several times and hold it down. Open the bleeder screw about half a turn, let the old fluid flow out, and close the bleeder screw before the helper releases the pedal.
- Repeat step 6 until clean, fresh fluid with no air bubbles comes out of the hose. Throughout the process, keep the reservoir at least 3/4 full, otherwise air will get into the system. Check the level after each wheel.
- Tighten the bleeder screw. The factory torque for similar Kia models is about 6-9 N·m (4.4-6.6 lb-ft) (check the exact value for your vehicle in the manufacturer's service manual). The bleeder screw is fragile, so don't overtighten it. Install the cap.
- Repeat steps 5-8 for the remaining wheels in the order given.
- Fill the reservoir to the MAX mark and close the cap.
- Press the pedal 10-15 times: it should feel firm, with no sinking or sponginess. If the pedal is soft, bleed the brakes again.
- Inspect the bleeder screws and hoses for leaks and wipe up any spilled fluid. Install the wheels, lower the vehicle, and tighten the lug nuts with a torque wrench to spec (usually about 90-110 N·m (66-81 lb-ft); check the exact value in the service manual).
- Take a test drive at low speed in an open area and test the brakes several times before getting onto the road. Dispose of the old fluid at a collection facility, because it is toxic.
- The replacement interval is usually 2 years, or sooner if the fluid has turned dark.
Common mistakes and warnings
- The brakes are a safety system
- If you don't have experience, leave the job to a repair shop
- If the pedal stays soft after bleeding, or the brake or ABS warning light is on, don't drive the vehicle until the cause is fixed
- Brake fluid is harmful to the eyes and eats away paint
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →