← Sedona Kia Sedona repair manuals →

Kia Sedona 3.5 V6 G6DN (2021): Throttle Body Assembly Replacement with Position Sensor

On the 2021 Sedona, the throttle is electronically controlled. The position sensors are built into the throttle body, and the parts catalog lists the throttle actuator as a single assembly. For that reason, the sensor is usually not replaced separately. Instead, the complete throttle body assembly is installed. Signs of a fault: codes for the sensor or throttle circuit, unstable idle, hesitation under acceleration, and limp mode. After replacement, you need to clear the codes and perform a throttle relearn with a scan tool.

DifficultyMedium Time1-1.5 hours Steps14

Parts

4
№PartGenuine part no.Alternatives
01 Complete throttle body assembly (ETC actuator with position sensors) for 3.5 V6 Lambda IIFind on Amazon → AlternativesHitachiBoschDenso
02 Throttle body gasketnewFind on Amazon →
03 Air intake ductif neededFind on Amazon → 28210-A9100
28140-A9100
04 Clampsif neededFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

6

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

14 steps
  1. Confirm the fault with a scan tool. Read the codes and the live throttle position sensor values. With the throttle closed and the ignition on, the readings should be stable and change smoothly as you press the pedal. If the code remains after you check the connector and wiring, that points to replacing the assembly. First inspect the connector for corrosion, a poor lock fit, and damaged wires.
  2. The engine must be completely cold. Turn the ignition off and disconnect the negative battery terminal. Wait 5-10 minutes so the capacitors in the control modules discharge.
  3. For access, remove the engine cover. Then remove the air duct that runs from the air filter housing to the throttle body. To do this, loosen the clamp at the throttle body, unclip the connectors and hoses for the sensors (mass airflow sensor, crankcase ventilation), and move the duct aside.
  4. Disconnect the throttle body electrical connector. To do this, press the locking tab and pull the connector off. Inspect the terminals.
  5. The throttle body is usually heated by engine coolant. If coolant hoses run to it on your vehicle, set a drain pan and rags underneath. Do not disconnect the hoses until the engine has cooled. Pinch the hoses off or be ready for a small amount of coolant to leak out, then remove the clamps and hoses. If there are no hoses, skip this step.
  6. Remove the bolts that secure the throttle body to the intake manifold (usually 3-4 bolts). Remove the assembly and the old gasket. Do not push on the throttle plate with your finger or force it open by hand, because the electric actuator is easily damaged.
  7. Clean the mating surface on the intake with a clean rag, and keep debris out of the manifold. Cover the opening with a lint-free rag while you work.
  8. Compare the new assembly with the old one: housing shape, connector, hose fitting locations, and mounting holes. Install the new gasket.
  9. Place the assembly on the manifold and tighten the bolts in a crisscross pattern. Approximate torque: 10-23 N·m (7-17 lb-ft). Check the exact value for the 2021 Sedona against the manufacturer's specifications. Do not overtighten, because the housing is plastic or thin-walled aluminum.
  10. Plug in the throttle body connector until it clicks, and reconnect the coolant hoses, tightening the clamps. Install the air duct and reconnect all connectors and hoses. Reinstall the engine cover.
  11. Reconnect the negative battery terminal. Turn the ignition on for 10-15 seconds without starting the engine. The electronics will detect the throttle's end positions on their own.
  12. Clear the codes with the scan tool. If the control module has a throttle learn or adaptation function, run it from the scan tool menu. Start the engine and let it warm up. The idle speed should stabilize.
  13. If you disconnected the coolant hoses, check them for leaks and check the level in the coolant reservoir. Top off if needed with the engine cold.
  14. Take a 10-15 minute test drive. Make sure the pedal response is smooth, the Check Engine light is off, and the codes have not returned. If a code remains, check the wiring to the accelerator pedal and the connectors, as well as the engine control module itself.

Common mistakes and warnings

  • During replacement, do not use a strong solvent-based cleaner on the electric actuator, and do not apply lubricant to the throttle plate
  • Do not leave your fingers or tools in the throttle bore with the ignition on, because the plate can move
  • The sensor type (separate or integrated) and the bolt sizes depend on the specific trim and equipment
  • If you lack experience, or if codes and unstable idle persist after replacement, have the diagnosis and throttle relearn done by a repair shop with a professional scan tool
Spotted a mistake? Tell us →