← Sorento Prime

Kia Sorento Prime 2.4 GDI (2016): Cylinder Head Installation

The 2.4 GDI engine (185 hp) is a gasoline engine with a timing chain drive and direct injection. Installing the cylinder head is precise work that depends on clean surfaces, the correct tightening sequence and stages, and accurate timing mark alignment. The exact step-by-step procedure and torque values for this engine are not documented in open service sources, so the general principle for an aluminum head with torque-to-yield bolts is given below. Always verify torque values against the manufacturer's service manual.

DifficultyHard Time6-10 hourswith the head already removed and the parts prepared Steps13

Parts

6
№PartGenuine part no.Alternatives
01 Cylinder head gasket, 2.4 Theta II GDI (G4KJ)Find on Amazon → AlternativesVictor ReinzAjusaElring
02 Cylinder head bolt set (torque-to-yield, single-use)newFind on Amazon → 22320-2C400
22321-2C400
03 Engine gasket and seal set (valve cover gasket, spark plug well seals)Find on Amazon → AlternativesVictor ReinzAjusaElring
04 Engine oilFind on Amazon →
05 CoolantFind on Amazon →
06 Timing chain, guides and tensionerif neededFind on Amazon → 24351-2F000 AlternativesVictor ReinzAjusaElring
24510-2F000
24376-2F000
24377-2F600

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

11

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

13 steps
  1. Prepare the cylinder block. Use a scraper (plastic or soft aluminum) to carefully remove any remaining old gasket material from the block surface without scratching the aluminum. Do not let carbon deposits or debris fall into the cylinders or the oil and coolant passages: cover the cylinders with a clean cloth beforehand.
  2. Blow out the cylinder head bolt holes and remove any oil and coolant from them (otherwise hydraulic lock in the hole and incorrect tightening are possible). If necessary, run a thread chaser through the threads.
  3. Check the flatness of the cylinder head with a straightedge and feeler gauge along its length and across the diagonals. For the allowable warpage, see the manufacturer's service manual; if it is exceeded, the head must be resurfaced or replaced. Inspect the valve seats and valve guides, and check the valves for sealing (kerosene test) before installation.
  4. Set the crankshaft to top dead center (TDC) of cylinder 1 using the marks, so that the pistons are in a safe position relative to the valves. The camshafts must not be in a position where the valves are open and could be damaged when the head is seated.
  5. Place the new cylinder head gasket on the block without sealant (unless the service manual requires otherwise), with the "TOP" mark or arrow facing up. Check that the dowel sleeves and all oil and coolant holes line up.
  6. Carefully lower the cylinder head onto the dowel sleeves without shifting the gasket. Check that the head sits level, without tilting.
  7. Lubricate the threads and the underside of the head of the new bolts with a thin layer of engine oil (unless the service manual specifies dry threads). Thread the bolts in by hand until they make contact.
  8. Tighten the cylinder head bolts in a spiral pattern from the center outward, in several stages: first the initial torque, then the final torque, followed by an angle turn to the specified angle (usually in two stages). Use the torque and angle values for the G4KJ strictly as given in the manufacturer's service manual; do not replace the stages with a single tightening.
  9. Install the camshafts and caps according to the marks, and tighten the caps gradually and evenly in the sequence given in the service manual; torque values are per the service manual.
  10. Fit the timing chain according to the marks, then install the guides and the tensioner. Check that all marks on the sprockets and the crankshaft line up. Turn the crankshaft by hand two full revolutions in the normal direction of rotation, then check the marks again. If the marks do not line up or you feel resistance, stop and find the cause.
  11. Install the valve cover with a new gasket, the spark plugs and ignition coils, the high-pressure fuel rail with new seals, and the intake and exhaust manifolds with new gaskets. Tighten to the torque values in the service manual, following the correct sequence.
  12. Reconnect the sensor connectors and wiring harnesses, the coolant hoses, and the crankcase ventilation hoses. Fill with coolant and bleed the air from the system (bleeding per the service manual); change the engine oil and oil filter if necessary.
  13. Start the engine and let it warm up until the thermostat opens. Check for leaks, smooth running and the absence of fault codes. After the mileage interval recommended by the manufacturer, recheck the coolant and oil levels and look again for leaks.

Common mistakes and warnings

  • The cylinder head bolts on this engine are torque-to-yield, so reusing them is not acceptable; always install new ones
  • An incorrect tightening sequence or torque leads to head distortion, combustion gas leaks and a repeat head gasket failure
  • A direct-injection engine is sensitive to cleanliness and to the correct sealing of the high-pressure fuel rail; if you lack experience, it is better to leave this job to a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →