← Sportage Kia Sportage repair manuals →

Kia Sportage (1st generation, JA): Power Steering Fluid Diagnosis and Replacement

When people search for "power steering," they usually mean power steering service: fluid replacement, leak diagnosis, noise, or a stiff steering wheel. On the first-generation Sportage, the power steering pump is belt-driven from the crankshaft, so first check the fluid level and the belt tension. Below are the fluid replacement procedure and basic diagnostics.

DifficultyEasy Time40-60 minutes Steps9

Parts

6
№PartGenuine part no.
01 Power steering fluid, ATF Dexron II/III typeabout 1-1.5 L (1.1-1.6 qt)Find on Amazon →
02 High-pressure power steering hoseif leaking or wornFind on Amazon → 0K012-32490C
03 Power steering return hoseif leaking or wornFind on Amazon → 0K022-32471B
0K012-32471B
04 Hose clampsif leaking or wornFind on Amazon →
05 Power steering pump drive beltif leaking or wornFind on Amazon → 0K65B-15907C
06 Steering rack sealsif leaking or wornFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

8

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 4 more. See manuals →

Step by step

9 steps
  1. With the engine cold and the car on level ground, open the hood and locate the power steering reservoir. Check the level against the MIN/MAX marks on the reservoir or the dipstick in the cap. The fluid should be clear, red or amber, with no foam and no burnt smell.
  2. Inspect the high-pressure and return hoses, their connections to the pump and the steering rack, and the steering rack boots. Traces of oil and streaks indicate a leak, which must be fixed before replacing the fluid.
  3. Inspect the power steering pump drive belt. Cracks, a glazed surface, or slack cause a squeal when turning the wheel and weak assist. Belt deflection under finger pressure should be small, about 8-12 mm. Tighten the belt with the adjusting bolt or replace it.
  4. To replace the fluid, remove it from the reservoir with a syringe or extractor bulb. Disconnect the return hose from the reservoir, place it in a container, and plug the reservoir port or leave the hose connected to the container.
  5. Lift the front wheels off the ground. Do not start the engine to flush the system. With the engine off, turn the steering wheel from lock to lock by hand to push the old fluid out of the rack. Alternatively, crank the engine briefly with the starter for 2-3 seconds at a time until the fluid comes out clean. This is faster, but make sure the reservoir never runs empty.
  6. Reconnect the return hose, using a new clamp if necessary. Fill with fresh fluid to the MAX mark.
  7. To bleed the air with the engine off, turn the steering wheel from lock to lock several times. Then start the engine and, at idle, turn the wheel in both directions without holding it at full lock for more than 3-5 seconds. Keep topping up the fluid until the level stops dropping and the bubbles in the reservoir disappear.
  8. With the engine running, check the connections for leaks. Lower the car onto its wheels and take a test drive. Afterward, recheck the level with the engine warm.
  9. If the steering is stiff, whines, or hums after the replacement, check the fluid level and air in the system. Then check the belt. After that, check the pump (noise, leaks at the shaft) and the condition of the rack (leaks at the boots, uneven assist). Pump or rack repairs are best left to a professional.

Common mistakes and warnings

  • Steering is a safety-critical system
  • If the steering behaves unnaturally after the work, develops play, leaks, or suddenly loses assist, do not drive the car and take it to a repair shop
  • Do not mix different types of fluid, and do not run the engine with no fluid in the reservoir: the pump can be destroyed within seconds
Spotted a mistake? Tell us →