Autopapyrus · Lada 2108-09 Samara (2003)
https://autopapyrus.com/catalog/lada/2108-09/guides/removing-the-dashboard-instrument-panel/
https://autopapyrus.com/catalog/lada/2108-09/guides/removing-the-dashboard-instrument-panel/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lada 2108-09 Samara (2003): Instrument Panel (Dashboard) Removal
The Samara dashboard is held by five screws, but to reach them you first have to remove the trim panels, instrument cluster, steering column stalk switch and steering wheel. The work is done inside the cabin and needs no special tools, but it is painstaking. A helper is useful but not required. This job is part of heater removal. The factory does not specify torque values for these fasteners: tighten plastic parts and screws moderately, without jerking.
Key figures
- Dash screws themselves5 pieces, 4 in the corners (the two upper ones under caps) and 1 in the glove box, see step 20
- Heater lever bracket screws4 pieces, removed with a Phillips screwdriver in step 4
- Socket for the steering wheel nut24 mm. In step 15, loosen it but do not remove it completely, so the wheel does not fly into your face
- Steering column shroud screws6 pieces, step 5. Without removing them you cannot reach the ignition switch and stalk switch
- Heater mounting nuts4 pieces, 10 mm socket, step 24. Needed if you are removing the heater together with the dash
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the panel screws, wheel nut and column cover are
Tap to enlarge
- 1Panel screws: 4 in the corners. The two upper ones have plugs: pry them off with a flat screwdriver and remove all four (step 20).
- 2Screw on the back wall of the glove box: the fifth panel screw, remove it too.
- 3Steering wheel nut under the horn pad: 24 socket with extension. Loosen but do not remove it fully, strike the wheel from below with your palm, then unscrew.
- 4Steering column cover: two halves, 6 screws. Remove both halves and the ignition lock trim.
- 5Heater and vent levers: pull off the knobs, remove the 4 bracket screws with a Phillips screwdriver.
Parts
5| № | Part |
|---|---|
| 01 | Plastic dash screw capsspareFind on Amazon → |
| 02 | Plastic switch mounting nutsspareFind on Amazon → |
| 03 | Trim mounting screw setFind on Amazon → |
| 04 | Heater hose clampsif the dash is removed to service the heaterFind on Amazon → |
| 05 | Heater valve pipe sealif the dash is removed to service the heaterFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
10Step by step
32 steps · 7 stagesStage 1 of 7 Preparation 3 steps
- Park the car on a level surface with the wheels pointing straight ahead, and do not touch the steering wheel. Disconnect the cable from the negative battery terminal.
- Photograph or label all connectors and wires you will disconnect. This makes reassembly much easier.
- If the dash is being removed to service the heater, plan ahead for draining the coolant. Draining is not needed for the dash itself.
Stage 2 of 7 Removing trim and controls 6 steps
- Remove the knobs from the heater and ventilation control levers. Using a Phillips screwdriver, remove the 4 screws holding the lever bracket and take the bracket off.
- Remove the 6 screws of the steering column shroud. Take off both halves of the shroud and the ignition switch trim.
- Remove the knob and scale of the headlight leveling control. Remove the knob of the instrument lighting switch.
- Remove the 4 screws of the instrument panel console trim. Pull the trim toward you and disconnect the wires from the cigarette lighter and its illumination bulb.
- Disconnect the wires from the exterior lighting switch and from the hazard, fog light and rear window defogger switches. Pull the switch block out toward you.
- Using a short Phillips screwdriver, remove the 2 screws of the retaining springs of the instrument cluster visor (they are on the inner upper wall of the visor). Pull the visor toward you by its upper part and remove it.
Stage 3 of 7 Instrument cluster and steering column components 4 steps
- Using an 8 mm socket, loosen the clamp bolt of the stalk switch on the steering shaft. Disconnect the wires and remove the switch.
- Pull the instrument cluster toward you to reach the connectors. On cars with a mechanical speedometer drive, open the hood and unscrew the cable sheath nut at the transmission drive, then the nut at the speedometer itself. Using pliers, pull out the cotter pin that secures the trip meter reset cable and remove the cable. On cars with an electronic speedometer, it is enough to disconnect the connectors.
- Disconnect the electrical wires and the rubber fuel economy gauge tube (if fitted) from the instrument cluster. Remove the instrument cluster.
- On carbureted cars, disconnect the choke cable from the carburetor. Unscrew the bracket and remove the choke control knob together with the cable. On fuel-injected cars, this step does not apply.
Stage 4 of 7 Steering wheel and ignition switch 5 steps
- Remove the horn button cover from the steering wheel.
- Using a 24 mm socket with an extension, loosen the steering wheel nut, but do not remove it completely: leave a few turns of thread engaged. Strike the steering wheel sharply from below with the palm of your hand to knock it loose from the shaft. If the nut is removed completely, the wheel may come off and hit you in the face.
- Now remove the nut completely and take off the steering wheel. When reassembling, use the manufacturer's specified torque for the nut.
- Disconnect the ignition switch connector, remove its mounting screws and take off the switch assembly. The heads of the switch mounting bolts are often stripped. Do not use excessive force; drill them out if necessary.
- Unscrew the nut and remove the headlight leveling control, if it is still attached. Remove the mounting screws of the lighting switch and the plastic nuts that hold the switches to the dash (21 mm socket).
Stage 5 of 7 Removing the dash 4 steps
- Remove the 2 screws that attach the instrument panel console to the heater bracket.
- Remove the 5 dash mounting screws: 4 in the corners of the dash (the two upper ones are covered with caps; pry the caps off with a flat-blade screwdriver) and 1 on the glove box side, on its rear wall.
- Check that no wires, cables or hoses remain connected anywhere. Carefully pull the dash toward you, with a helper if necessary, and take it out of the cabin.
- If necessary, remove the heating and ventilation ducts and nozzles from the dash.
Stage 6 of 7 If the dash is removed to service the heater 4 steps
- Remove the 2 screws of the floor tunnel trim and take off the cabin interior ventilation duct.
- Using a 10 mm socket, remove the 4 nuts that attach the heater to the body. The front left nut also holds the ground wire of the blower motor; remove it.
- Open the heater valve and drain the coolant by unscrewing the plug on the block with a 13 mm wrench. From below, loosen the clamps of the valve hoses and remove the hoses.
- Using a 10 mm wrench, remove the 2 nuts that attach the valve to the firewall, remove the seal from the valve pipes and take out the complete heater assembly.
Stage 7 of 7 Installation and check 6 steps
- Install in the reverse order. Before installation, tighten the duct mounting screws on the dash.
- Secure the stalk switch in the position that ensures reliable contact of the horn circuit.
- Install the steering wheel with the wheels pointing straight ahead and tighten the nut with a 24 mm socket to the manufacturer's specified torque. Tighten the dash and trim screws moderately so the plastic does not crack.
- When installing the instrument cluster visor, insert the retaining springs into the visor slots, secure them with the screws and put the visor in place.
- Seat the heater hoses (if removed) with sealant and tighten them with screw-type clamps. Top off the coolant and warm up the engine, checking for leaks and air pockets.
- Reconnect the battery. Check the operation of the horn, turn signals, lights, hazard lights, instrument lighting, gauges, cigarette lighter, heater and blower.
Common mistakes and warnings
- Work with the battery disconnected
- There may be wires near the steering wheel, so avoid short circuits
- Do not unscrew the steering wheel nut completely before knocking the wheel off the shaft
- Watch the steering wheel position during reassembly: wheels straight and spokes straight
- For a 2003 car, check which engine you have (carburetor or fuel injection) and which speedometer drive it uses
- Steps 11 and 13 depend on this