Autopapyrus · Lada 2114 1.6 8V (2012)
https://autopapyrus.com/catalog/lada/2114/guides/valve-clearance-adjustment/
https://autopapyrus.com/catalog/lada/2114/guides/valve-clearance-adjustment/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lada 2114 1.6 8V (2012): Valve Clearance Adjustment
On the 8-valve 1.6 engine, the clearance between the camshaft lobe and the tappet is set by choosing the thickness of the adjusting shim. Nominal clearances on a cold engine (about 20 °C): intake 0.15-0.25 mm, exhaust 0.30-0.40 mm. It is recommended to check them, and adjust if needed, every 20-30 thousand km, and also if a metallic knocking noise or loss of power appears.
Key figures
- Intake valve clearancecheck with a feeler gauge on a cold engine (steps 6-8 and 13)0.15-0.25 mm
- Exhaust valve clearancesame procedure, slightly larger than intake (steps 6-8 and 13)0.30-0.40 mm
- Engine temperature during adjustmentthe engine must be completely cold (step 1)about 20 °C
- Crankshaft rotation after TDC for the first checkfor measuring the valves under cams 1 and 3 (step 6)40-50° (about 3 teeth of the camshaft pulley)
- Check intervalhow often the clearances should be checked20-30 thousand km
- Shim thickness calculationused to select the new shim (step 11)Z = Y + X − 0.2 mm (intake), Z = Y + X − 0.3 mm (exhaust)
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part |
|---|---|
| 01 | Valve tappet adjusting shims (VAZ 8-valve engine)of the required thickness after measuring clearancesFind on Amazon → |
| 02 | Valve cover gasketFind on Amazon → |
| 03 | Mating-surface sealantif neededFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8- flat feeler gauge set Amazon →
- valve clearance adjusting tool (presses down the tappet and locks it in place) Amazon →
- 0-25 mm micrometer Amazon →
- tweezers Amazon →
- 17 or 19 mm wrench for turning the crankshaft by the pulley bolt Amazon →
- syringe or bulb for oil Amazon →
- sockets and wrenches for removing the valve cover and timing belt cover Amazon →
- torque wrench Amazon →
Step by step
15 steps- Let the engine cool down completely and do the adjustment at a temperature of about 20 °C. On a hot engine the metal is expanded and the measurements will be wrong.
- Remove the valve cover and the front protective timing belt cover. Check the fastener torque specs against the manufacturer's manual. The valve cover usually takes a low torque, only a few N·m. Tighten evenly.
- Remove any leftover oil around the tappets with a syringe or rubber bulb, so the oil doesn't interfere with the measurements or get under the shims.
- Install the adjusting tool on the head studs and secure it with the valve cover mounting nuts.
- To turn the crankshaft, use a 17 or 19 mm wrench on the pulley bolt. Turn it clockwise only. You can also turn it by the flywheel teeth with a screwdriver, after removing the rubber plug from the opening in the clutch housing. Set the No. 1 cylinder piston to TDC on the compression stroke using the marks.
- You can only check the clearance on valves that are closed, meaning the cam is not pressing on the tappet. From TDC, turn the crankshaft another 40-50° (about 3 teeth of the camshaft pulley) and check the valves under cams 1 and 3 with a feeler gauge, counting from the camshaft pulley. A feeler gauge of nominal thickness should fit between the cam and the shim with slight drag.
- Check the remaining valves one after another, turning the crankshaft so the cam lobes face away from the tappet. Angles from TDC on the compression stroke and the cam pairs: about 40-50° — cams 1 and 3; about 220-230° — cams 5 and 2; 400-410° — cams 8 and 6; 580-590° — cams 4 and 7.
- Write down the measured clearance X for each valve. If any valve is out of spec, note its number. Measure all of them first, then calculate and buy the shims.
- For valves that need a new shim, turn the tappet with its slot facing you. Use the tool to press the tappet down, holding it with a screwdriver in the slot so it doesn't rotate. Lock the tappet in the lowered position with the tool's retainer.
- Remove the old shim with tweezers. The thickness is stamped on the side that doesn't contact the cam. If the marking has worn off, measure the shim with a micrometer; this value is Y.
- Calculate the thickness of the new shim, Z. For intake valves: Z = Y + X − 0.2 mm. For exhaust valves: Z = Y + X − 0.3 mm. Choose the shim closest to the calculated value.
- Install the new shim in the tappet with the marking facing down. Press the tappet with the tool, remove the retainer, then remove the tool.
- Turn the engine a couple of revolutions clockwise and recheck all clearances with the feeler gauge. They should be within the nominal values.
- Remove the adjusting tool, reinstall the timing belt cover and the valve cover with a new gasket, and tighten the fasteners evenly in a crisscross pattern to the manufacturer's specification.
- Start the engine and listen to it at different RPMs. There should be no unusual metallic knocking and no oil leaks.
Common mistakes and warnings
- Turn the crankshaft clockwise only
- Do not adjust the clearances on a hot engine
- Clearances that are too small lead to burned valves and seats, and clearances that are too large lead to knocking and loss of power
- Check the shim sizes and the tightening torques for the valve cover and the belt cover against the manufacturer's manual, so you don't strip threads or over-compress the gasket