Autopapyrus · Lada 2115 (2007)
https://autopapyrus.com/catalog/lada/2115/guides/ignition-lock-cylinder-replacement/
https://autopapyrus.com/catalog/lada/2115/guides/ignition-lock-cylinder-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lada 2115 (2007): Ignition Lock Cylinder Replacement
On the VAZ-2115, the lock cylinder sits in the lock housing on the steering column under the steering wheel. To reach it, you remove the plastic column shrouds and, in most cases, the steering wheel along with the column stalk switches. The lock housing is held by a clamp with shear bolts. If the cylinder is worn, binds, or the key won't turn, it is easiest to install a complete lock assembly. Replace the cylinder alone only when the housing and contact group are in good condition.
Key figures
- Number of shear bolts on the lock clampthis is how many bolts hold the lock on the steering column; they must either be driven out with a chisel during removal or tightened until the heads shear off during installation (steps 8-10 and 18)4
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the ignition lock cylinder is and how to remove it
Tap to enlarge
- 1Steering column: the lock sits on it. Reach it after removing the covers, steering wheel and column switches.
- 2Lock housing: remove it from the column as a whole, then take the cylinder out of it.
- 3Lock cylinder: this is what you replace. With the key in position, press the retainer with a thin screwdriver through the side hole and pull the cylinder out by the key.
- 42 mm drill: only if there is no key or the cylinder does not turn. Drill shallowly near the retainer and press it with the drill.
- 5Shear-head clamp bolts (4 pcs): hold the lock on the column. Knock them out with a chisel when removing; tighten new ones until the heads shear off.
- 6Wiring connector: it is disconnected from the lock before removal.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Ignition lock assembly for (with starter re-engagement protection)Find on Amazon → | AlternativesLada-ImageAvtoelektrikaKraft |
| 02 | Ignition lock cylinder with key setinstead of the complete lock assemblyFind on Amazon → | AlternativesLada-ImageAvtoelektrikaKraft |
| 03 | Ignition switch contact groupif neededFind on Amazon → | AlternativesLada-ImageAvtoelektrikaKraft |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6Step by step
23 steps · 6 stagesStage 1 of 6 Preparation 3 steps
- Park the car on level ground with the wheels pointing straight ahead, put it in first gear, and set the parking brake. The steering must not be locked: insert the key and gently rock the steering wheel. If the key won't go in or won't turn, you will have to remove the cylinder by drilling (step 13).
- Disconnect the cable from the negative battery terminal. Wait a few minutes. This car has no airbags, but disconnecting power is still mandatory.
- Prepare the work area: slide the driver's seat back and lay a cloth over your lap and the floor so you don't lose small screws and clips.
Stage 2 of 6 Accessing the lock 4 steps
- Remove the screws and take off the upper and lower plastic steering column shrouds.
- Remove the steering wheel. Pry out the center cap, remove the steering wheel retaining nut, mark the position of the wheel relative to the shaft with paint, and take the wheel off by rocking it toward you. When reassembling, tighten the nut to the manufacturer's specification.
- Remove the column stalk switches: loosen the clamp, disconnect the wiring connectors, and set the switch assembly aside.
- Disconnect the wiring harness connector from the ignition lock and the lock illumination bulb socket connector.
Stage 3 of 6 Removing the lock 3 steps
- Locate the four bolts that secure the lock clamp to the steering column. They have shear heads, so a regular wrench won't grip them.
- If the bolts have been sheared before, drive them around by tapping with a hammer on a thin chisel, turning them counterclockwise. If the heads are intact, loosen them the same way.
- Fully remove the bolts from the lock housing and take the lock off the steering column.
Stage 4 of 6 Replacing the cylinder 6 steps
- Secure the lock in a vise with soft jaws or on a workbench. Insert the original key and turn it to the position where the black plastic or metal cylinder retainer is visible opposite the side hole in the housing.
- Use a thin screwdriver or awl to press the retainer through the hole in the housing and, while holding it down, pull the cylinder out by the key.
- If you don't have the key or the cylinder won't turn, carefully drill the housing with a 2 mm bit in the area of the retainer plate (roughly 10 mm from the collar). Press the retainer with the same bit and pull the cylinder out. Drill only shallowly so you don't damage the contact group.
- If necessary, remove the contact group. Release the clips on one side, then the other, and take off the plastic cover. Release the two clips on each side of the cover and remove the contact group together with the light guide. Clean oxidized contacts with fine sandpaper. If they are badly burned, replace the contact group.
- Install the new cylinder: insert it with the key in the position matching its position in the housing until the retainer clicks. Check that the key can be removed only in the zero position.
- Assemble the contact group: the tab on the lock cylinder must sit between the two tabs on the inner surface of the light guide. Close the cover onto its clips.
Stage 5 of 6 Installation and reassembly 4 steps
- Before installing the lock on the column, insert the key and turn it from position "0" to retract the anti-theft locking tongue.
- Fit the lock onto the steering column and tighten the clamp with new shear bolts evenly, working in a circle, until the heads shear off. Tighten to the manufacturer's specification.
- Reconnect the wiring harness connector and the lock illumination connector.
- Install the column stalk switches, then the steering wheel according to your marks (wheels pointing straight ahead). Tighten the steering wheel nut to specification, then install the center cap and the column shrouds.
Stage 6 of 6 Testing 3 steps
- Reconnect the negative terminal. Check the key positions: "0" — everything off, I — ignition and instruments on, II — starter, III (if equipped) — parking only.
- Start the engine. Check that the key returns from the starter position, and that on a repeat start attempt the starter does not engage until the key is turned back to "0" (starter protection).
- Shut off the engine, remove the key, and make sure the steering locks. Check the lock illumination and the column stalk switches (turn signals, lights, wipers, horn).
Common mistakes and warnings
- Do not replace the lock clamp shear bolts with ordinary bolts: they are a standard anti-theft feature
- Do not tighten the steering wheel without alignment marks: a misaligned wheel will sit off-center when driving straight
- If you are not confident working with the steering and electrical systems, take the car to a repair shop: the steering system is safety-critical