← Iskra

Lada Iskra (2026): Heater Blower Motor (Cabin Fan) Replacement

The heater blower motor is located in the heater housing under the dashboard on the passenger side. It is usually accessed by removing the lower glove box. Signs of a fault: the blower does not run at any speed, or it howls, squeaks or rattles, while the fuse and connector are intact. The torque values below are approximate: the fasteners are small and plastic, so tighten them gently.

DifficultyMedium Time1-2 hours Steps25

Diagram: where the heater motor, its connector and latch are and how the motor looks removed

Heater motor seen from below and after removalView from below into the heater housingMotor removed: side viewfixed further onmarknut on the hublower the motor down1Round fan housing5Wire harness2Motor with impeller3Power connector4Latch tabblue tab in the centreTap to enlarge
  1. 1Round fan housing at the bottom of the heater unit: the motor sits in it. Spokes and a blue tab are visible inside.
  2. 2Motor with impeller: drum with blades, hub with nut, flange on top. Lower it and pull it out of the housing; do not touch the heater core.
  3. 3Power connector at the motor flange: press the latch and pull the connector, not the wires.
  4. 4Bayonet latch tab on the flange rim next to the mark: press it down and turn the motor counterclockwise to the mark.
  5. 5Wire harness near the housing: do not yank it or break its clips.

Parts

2
№PartAlternatives
01 Heater blower motor with fan wheel for Lada Iskra, 12 VFind on Amazon → AlternativesLuzarNissensValeo
02 Heater blower speed controller (resistor or electronic module)if the original is meltedFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5

Step by step

25 steps · 5 stages
Stage 1 of 5 Preparation and diagnosis 4 steps
  1. Make sure the motor is the cause. Check the heater blower fuse in the fuse box, using the diagram on its cover.
  2. Turn the ignition on and set the fan control to maximum. If the blower does not work, check for 12 V at the motor connector. If voltage is present but the motor does not turn, the motor is faulty. If there is no voltage, look for the cause in the speed controller, the wiring or the switch.
  3. Park the vehicle on level ground, turn the ignition off and disconnect the negative battery terminal. Wait 5-10 minutes.
  4. Slide the front passenger seat all the way back to make room to work. Lay a clean towel on the floor mat for small parts.
Stage 2 of 5 Accessing the motor 5 steps
  1. Open the lower glove box and empty it.
  2. Remove the glove box mounting screws (they may be inside and along the top) and unclip the side travel stops. Pry the lower clips with a plastic trim tool. Lower the glove box and remove it.
  3. If there is a lower trim panel or an air duct behind the glove box at the passenger's feet, remove it. Release the clips carefully, do not break them.
  4. Shine the flashlight upward: find the round blower housing at the bottom of the heater unit, its connector and the speed controller.
  5. If the wiring or the controller presses against the dashboard, loosen the nearest dashboard mounting screw. You do not need to remove it completely.
Stage 3 of 5 Removing the motor 5 steps
  1. Disconnect the blower power connector. Press the locking tab and pull on the connector, not on the wires.
  2. If the speed controller is mounted on the blower housing, disconnect its connector and remove its fasteners.
  3. If the motor is held by a bayonet lock, press the locking tab down and turn the motor counterclockwise a few centimeters to the mark. If it is secured by screws around the flange, remove them with a Phillips screwdriver while supporting the motor.
  4. Lower the motor and carefully pull it out of the housing. The fan wheel should pass through the opening without catching. Do not touch the heater core.
  5. Inspect the inside of the heater housing. Remove leaves, debris and any crumbled plastic. Debris is often the reason a new motor howls.
Stage 4 of 5 Installing the new motor 5 steps
  1. Compare the new motor with the old one: mounting flange, connector orientation, and the size and direction of the fan blades. Transfer the rubber seals and dampers to the new motor if they are separate parts.
  2. Connect the new motor to the connector and test it briefly. Reconnect the battery and turn the ignition on. The motor should spin smoothly and quietly. Then disconnect the battery again.
  3. Insert the motor into the housing, aligning the marks. Check that the fan wheel spins when pushed with a finger and does not rub on anything.
  4. Secure the motor: turn it clockwise until the lock clicks (bayonet), or tighten the flange screws gently (guideline 1-2 N·m (9-18 lb-in); do not overtighten the plastic).
  5. Connect the power connector and the speed controller. Make sure the wires cannot touch the spinning fan wheel and are not pinched.
Stage 5 of 5 Reassembly and testing 6 steps
  1. If you loosened the dashboard screw, snug it back down lightly.
  2. Reinstall the air duct or lower panel, then the glove box. Secure the screws and clips.
  3. Reconnect the negative battery terminal. Turn the ignition on, then run through all the fan speeds. The sound should be steady, without vibration or squealing.
  4. Check the airflow mode selection (windshield, feet, face) and recirculation. The airflow should be strong and noticeable.
  5. Start the engine and check the heater with the engine at operating temperature.
  6. If the blower still does not work, check the speed controller and the fuse.

Common mistakes and warnings

  • Do all the work with the battery disconnected
  • Airbag wiring runs nearby, so do not yank the harnesses behind the dashboard or break the clips
  • If a panel's plastic has cracked, replace the part
  • Do not remove the fan wheel from the rotor unless necessary: the rotor and fan wheel are balanced together, and the motor may vibrate afterward
Spotted a mistake? Tell us →