https://autopapyrus.com/catalog/lada/largus/guides/evaporative-canister-removal-and-installation/
Lada Largus 1.6 16V (VAZ-21129) (2020): Evaporative Canister Removal and Installation
The canister traps gasoline vapors from the fuel tank and sends them to the intake through the purge valve. On the Largus it is located in the right front wheel well, ahead of the right front wheel, behind the wheel arch liner. It is held by two 13 mm nuts. The procedure is the same regardless of engine.
Key figures
- Canister mounting nut size13 mm (socket with extension). Two nuts hold the canister; they are removed in step 7 and tightened in step 9.
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the canister is and what to disconnect and unbolt
- 1Purge valve: the cylinder with a flange on top of the canister. It is replaced together with the canister and is not sold separately.
- 2Side hose of the valve: press the spring clip and pull the hose straight along the fitting axis, without jerking.
- 3Top hose of the valve: press the spring clip likewise and pull along the fitting axis, without tilting.
- 4Vent hose on the canister: just pull it off.
- 5Two 13 mm nuts on the bracket studs: undo with a socket and extension, then remove the canister. Tighten moderately, do not overtighten.
- 6Valve electrical connector: disconnect it before removing the canister.
Part
| № | Part |
|---|---|
| 01 | Fuel vapor canister assembly with purge solenoid valve (Largus 1.6 16V)valve is not sold separately; the whole assembly is replacedFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
4Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
13 steps- Park the car on a level surface or on a lift, set the parking brake, and turn the ignition off. Disconnect the negative (-) battery terminal.
- Get access to the canister. On a lift, remove the right skid plate under the front bumper. On the ground, it is easier to remove the right front wheel arch liner: raise the wheel off the ground, remove it if necessary, and remove the liner fasteners.
- Inspect the assembly. It has four connections: the vapor supply hose from the tank, the vapor outlet hose to the intake (both on the purge valve), the vent hose (breather), and the valve's electrical connector.
- Press the spring clips on the ends of the tank vapor hose and the intake outlet hose. Pull each hose off the valve fitting straight along the fitting's axis, without jerking or twisting.
- Pull the vent hose (breather) off the canister.
- Disconnect the purge valve electrical connector.
- Using a 13 mm socket with an extension, remove the two nuts that hold the canister, then remove it. If you need to take the canister off its bracket, slide it up so the rubber retainer comes out of the eyelet, remove the retainer, and lift the canister off.
- Before installing, compare the new assembly with the old one: the fittings and valve should be identical. Wipe the mounting area clean of dirt.
- Install the canister in place (with the rubber retainer, if you removed it) and tighten the two 13 mm nuts. The tightening torque is not given in publicly available sources: tighten moderately without overtightening, and check the value against the manufacturer's specifications.
- Connect the valve connector and push on the vent hose.
- Push the tank vapor hose and the intake outlet hose onto the fittings along their axes until the spring clips click. Tug on each one to make sure it holds.
- Install the wheel arch liner or skid plate and the wheel (tighten the wheel bolts to specification), then reconnect the battery.
- Start the engine and let it warm up. Check that there is no smell of gasoline and that the Check Engine light is off. A steady clicking of the purge valve while the engine is running is normal.
Common mistakes and warnings
- Work away from open flames and sparks, and do not smoke: gasoline vapors are present nearby
- Remove all hoses and clips without jerking, because the plastic fittings are brittle
- If the Check Engine light comes on after replacement or you smell gasoline, check that the hoses are seated properly
- If the valve clicks loudly and the noise bothers you, on some cars it is damped by mounting the canister on rubber vibration mounts, but the noise itself is normal valve operation