← Priora

Lada Priora (2008): Rear Seat Removal

On the Priora sedan, the rear seat consists of a cushion and a split seatback. The cushion is held by spring-loaded latches on the sides, and the seatback hooks onto the body with loops and hooks. Everything comes off by hand or with minimal tools. This guide is for the sedan. On the hatchback and wagon, the seatback folds and comes off differently.

DifficultyEasy Time15-30 minutes Steps20

Parts

2
№Part
01 Seatback latch loopif the mounts breakFind on Amazon →
02 Plastic seat cushion guidesif the mounts breakFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

3
  • Phillips screwdriver Amazon →
  • 10 mm socket with ratchet (needed only for removing the armrest and the latches) Amazon →
  • flat-blade screwdriver for prying off trim Amazon →

Step by step

20 steps · 5 stages
Stage 1 of 5 Preparation 2 steps
  1. Park the car on level ground, set the parking brake, and open the rear doors fully.
  2. Remove any loose items from the seat and from the pockets. If there are headrests, press each headrest's release button and, while holding it, pull the headrest up and out.
Stage 2 of 5 Cushion removal 4 steps
  1. Find the spring latches on the sides of the cushion. Press their handles on both sides.
  2. While holding the latches pressed, lift the front of the cushion slightly and pull it forward and up.
  3. If the cushion does not come free, check whether it is caught on the seat belts or the carpet. Do not use force, so you do not break the plastic clips.
  4. Lift the cushion out of the cabin and set it down on a clean surface.
Stage 3 of 5 Seatback removal 6 steps
  1. Open the trunk. On the trunk side, at the back of the seatback, unfasten the upholstery snaps, if your trim level has them.
  2. Pull up on the seatback latch loops: they will release the catch.
  3. Tilt the seatback forward slightly and release the movable loop from the fixed loop on the body.
  4. If the car has an armrest, use a Phillips screwdriver to remove the three screws of the armrest frame. Use a 10 mm socket to remove the two nuts of the armrest hinge, then take off the armrest together with its plastic frame.
  5. Lift the seatback hooks out of the body brackets and raise the seatback up. Remove the two halves one at a time.
  6. If the seat belts are in the way, carefully guide them through the slots without twisting the webbing.
Stage 4 of 5 Latches and inspection 3 steps
  1. If you need to replace the cushion latch, remove it with a Phillips screwdriver. To reach its base, take off the sill trim and undo the two 10 mm nuts.
  2. Inspect the loops, hooks, and brackets on the body. Straighten anything bent, and clean off any rust and treat the area.
  3. Wipe down the floor under the seat and check the wiring and carpet for moisture.
Stage 5 of 5 Installation 5 steps
  1. Install the seatback: set the hooks into the body brackets, engage the movable loops with the fixed ones, and press the seatback back until it clicks. Pull on the top of the seatback to make sure it holds.
  2. Install the armrest, if you removed it. Tighten the nuts and screws moderately: torque specifications are not given in the sources, so snug them until the fasteners do not wobble, without stripping them.
  3. Install the cushion: set the front edge onto the factory pins in the floor, then press down on the rear until the latches click.
  4. Insert the headrests until they lock.
  5. Check that the seat belts pull out freely and lock, and that the seatback and cushion latches are securely engaged.

Common mistakes and warnings

  • The seatback and cushion must lock fully: an unsecured seatback can shift onto passengers or into the cabin during hard braking
  • Do not force the plastic clips or damage the seat belts
  • If the belts have built-in pretensioners, do not strike them or apply strong force to them
Spotted a mistake? Tell us →