Autopapyrus · Lancia Thema (1st generation)
https://autopapyrus.com/catalog/lancia/thema/guides/ignition-switch-contact-block-replacement/
https://autopapyrus.com/catalog/lancia/thema/guides/ignition-switch-contact-block-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lancia Thema (1st generation): Ignition Switch Contact Block Replacement
The contact block is a plastic unit with contacts on the back of the ignition switch, under the steering column shroud. It supplies power to the ignition, the instrument cluster and the starter. If you are replacing only the electrical part, you usually don't need to remove the steering column. It is enough to take off the lower shroud and disconnect the connector. The exact procedure for this model is not documented in publicly available service materials, so below is the general procedure for switches of this type. Check the location of the mounting screws on your car visually.
Diagram: where the ignition switch contact block sits and how to remove it
Tap to enlarge
- 1Contact block: the black plastic block with contacts on the back of the ignition switch. Mark its position on the lock with a marker before removal. It has a locating tab: align the new one by it and by the marks.
- 2Two small screws hold the contact block to the lock body. Unscrew them and the block comes off (if it is held by latches, press them with a screwdriver).
- 3Connector with wiring harness: the plastic plug on the contact block. Photograph it and the wires, press the latch with a thin screwdriver without jerking and unplug it.
- 4Ignition lock: sits on the steering column, the contact block attaches to its back side.
- 5Steering column cover in two halves: first remove the screws and carefully separate the halves to reach the lock.
- 6Steering column: the lock sits on it under the cover. The column does not need to be removed.
Parts
2| № | Part |
|---|---|
| 01 | Lancia Thema I ignition switch contact blockelectrical part of the switch, attaches to the lock cylinderFind on Amazon → |
| 02 | Ignition lock with steering column lock, completeif the lock itself is faulty (key won't turn or won't lock in position)Find on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
13 steps- Park the car on level ground with the wheels pointing straight ahead and remove the key. Disconnect the negative battery terminal and wait a few minutes. This protects the electrical system from a short circuit and prevents accidental activation of the airbags or other circuits while you work.
- If the column height or reach adjustment is in the way, set the steering wheel to the most convenient position (lowered gives more room).
- Remove the lower and upper halves of the plastic steering column shroud. Remove the mounting screws on the bottom and sides (usually Phillips) and carefully separate the halves. Don't pull hard: if it won't come off, look for a hidden screw or clip. Don't disconnect the column stalk switches unless you have to.
- Find the ignition switch on the column. The contact block sits on its rear side, with a wiring harness and plastic connector going to it.
- Take a photo of the connector position and the wire colors so you can reassemble it correctly.
- Press the connector latch (with a thin flathead screwdriver if needed) and disconnect the connector. The latches are brittle, especially on old plastic, so work without jerking.
- Mark the position of the contact block on the switch with a marker. Remove the two small screws that hold it to the switch body (recessed, with small heads) and take off the block. If the block is held by clips, press them in with a screwdriver.
- Compare the old and new contact blocks: the shape, the number of contacts and the position of the actuator pin should match. Put the key in the "0" (off) position and make sure the new block is also in the "0" position, otherwise it will seat incorrectly.
- Install the new block in place using the marks and tighten the screws. The torque for such small screws is low, so tighten them moderately, without stripping the plastic (for the exact value, follow the manufacturer's specification).
- Treat the connector contacts with contact cleaner and plug in the connector until it clicks.
- Temporarily reconnect the battery and test operation without installing the shrouds: the "ignition", "start" and "off" positions, and the operation of the instruments, starter, lights and turn signals. If necessary, check with a multimeter for power at the relevant contacts.
- Disconnect the battery again, reinstall the steering column shrouds, tighten the screws and reconnect the battery.
- Check the operation of the key and the steering lock: with the key removed the steering wheel should lock, and with the key inserted it should turn freely.
Common mistakes and warnings
- Work with the battery disconnected
- If you need to replace not only the contact block but also the lock itself or the steering lock, note that on some cars of this period the lock is attached to the column with shear bolts
- These have to be drilled out or knocked out with a center punch, and new ones fitted during installation
- In that case, take the car to a repair shop, because the reliability of the steering lock affects safety
- Don't remove the key or defeat the steering lock while driving, and disconnect connectors only with the power off
- If the car has an immobilizer or an alarm, they may need to be checked after the replacement