Autopapyrus · Lexus GS S190 (2008)
https://autopapyrus.com/catalog/lexus/gs/guides/headlight-leveling-actuator-servo-motor-replacement/
https://autopapyrus.com/catalog/lexus/gs/guides/headlight-leveling-actuator-servo-motor-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lexus GS S190 (2008): Headlight Leveling Actuator Replacement
The leveling actuator tilts the headlight reflector up and down as the vehicle load changes. If the headlight points at the ground or at the sky and the actuator hums, that points to a failed actuator. The actuator plugs into the back of the headlight housing and is secured by turning it, like a bulb. For access, it is usually enough to remove the headlight from the vehicle and take out the bulbs. The procedure is described for a xenon headlight, and it is the same on the left and right sides.
Key figures
- Bumper side support screwsremove them in step 5 to get access to the headlight3 pcs
- Wait time after disconnecting the batteryso the xenon unit discharges before work (step 2)10-15 minutes
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Xenon headlight leveling actuator (motor)left or right, depending on the failed side; OE is more reliableFind on Amazon → | AlternativesTYCDepo |
| 02 | Headlight leveling actuator base sealnewFind on Amazon → | |
| 03 | Headlight bulb cover seal (gasket)newFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more.
See manuals →
Step by step
24 steps · 6 stagesStage 1 of 6 Preparation and diagnosis 3 steps
- Make sure the actuator is really the faulty part. Turn on the low beams and change the vehicle load or rock the body: the headlight should tilt slightly. Humming, steps with no movement, or a permanently "low" beam point to the actuator.
- Park the vehicle on a level surface and turn off the ignition and lights. The xenon igniter unit can hold voltage, so disconnect the battery terminal and wait 10-15 minutes.
- Open the hood. Inspect the actuator connector and wiring: sometimes the cause is an oxidized connector rather than the motor itself.
Stage 2 of 6 Headlight removal 4 steps
- Remove the side part of the bumper grille and the upper clips of the plastic trim above the headlight. Pull back the front part of the fender liner to reach the side fasteners.
- Remove the front bumper side support: it is held by 3 screws. Carefully pull the edge of the bumper aside with a plastic trim tool, without scratching the paint.
- Remove the headlight mounting bolts and screws, located on the top and on the side. Tighten to the manufacturer's specification; these are usually small body-panel mounting bolts.
- Disconnect the headlight connectors (main harness, xenon igniter unit, turn signal, parking light) by pressing the locking tabs. Pull the headlight out forward and place it lens-down on a soft cloth.
Stage 3 of 6 Accessing the actuator 4 steps
- Remove the rear bulb covers (xenon and low beam/high beam) and their seals. Replace the seals with new ones during reassembly, otherwise water will get into the headlight.
- Remove the bulb sockets without touching the glass of the bulbs with your fingers. Disconnect the bulb and xenon igniter unit connectors, and release the bulb spring retainer to move them out of the way.
- Disconnect the headlight harness and remove the side bulbs (parking light and turn signal) by turning the sockets.
- Locate the leveling actuator at the back of the housing, usually below or beside the reflector.
Stage 4 of 6 Actuator replacement 6 steps
- Disconnect the actuator connector if it is still connected.
- Align the marks (notches) on the actuator and the headlight housing and pull the actuator back slightly.
- Lower the tip of the actuator so that the rod disengages from the reflector, and take the actuator out of the housing.
- Remove the rubber seal from the actuator base and replace it with a new one. Wipe the mounting seat with a clean cloth.
- Insert the rod of the new actuator into the reflector, and turn the actuator until it locks, aligning the marks. The rod must snap onto the ball joint of the reflector.
- Connect the actuator connector. The actuator is supplied in the middle position, so do not turn it by hand before installing it.
Stage 5 of 6 Reassembly 3 steps
- Install the new seals, bulbs and covers in reverse order. The covers must seat tightly all the way around so they do not let water in.
- Connect the headlight connectors and set the headlight in its mounting positions. Tighten the mounting bolts and screws to the manufacturer's specification. Install the bumper side support with its 3 screws, then the trim clips, the fender liner and the grille.
- Connect the battery terminal.
Stage 6 of 6 Check 4 steps
- Turn on the ignition and the low beams. The actuator should make a short movement and settle at the position for the vehicle's load. There should be no humming and no errors on the instrument panel.
- Check the tilt of the beam pattern on a wall 5-10 meters away: the left and right headlights should be symmetrical.
- Perform the headlight aiming adjustment to the specification if the pattern differs from normal. It is required after the headlight has been removed.
- If a leveling error light is on after replacement, check the connector and harness and, if necessary, clear the error with a diagnostic scanner.
Common mistakes and warnings
- The xenon system operates at high voltage: do not touch the igniter unit contacts while the system is on, and be sure to disconnect the battery
- Do not touch the bulb glass with your hands
- New seals are mandatory: old ones let water in and the headlight fogs up
- The tightening torques for the headlight and bumper fasteners are approximate: check the exact values against the manufacturer's specification