Autopapyrus · Mazda Bongo 2.0 Diesel RF (1993)
https://autopapyrus.com/catalog/mazda/bongo/guides/checking-and-adjusting-valve-lash/
https://autopapyrus.com/catalog/mazda/bongo/guides/checking-and-adjusting-valve-lash/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Mazda Bongo 2.0 Diesel RF (1993): Checking and Adjusting Valve Lash
The RF 2.0 diesel engine (SOHC, 8 valves) requires periodic valve lash checks and adjustments every 80,000-100,000 km (50,000-62,000 mi). The valvetrain uses direct valve actuation through followers and adjusting screws. Adjustment must be done on a cold engine (oil temperature no higher than 40°C (104°F)).
Part
| № | Part |
|---|---|
| 01 | Valve cover gasketif replacement is neededFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Step by step
8 steps- Remove the valve cover: disconnect the crankcase ventilation hoses, remove the 8-10 mounting bolts around the perimeter, and carefully lift the cover straight up (do not damage the gasket).
- Turn the crankshaft clockwise until the No. 1 cylinder TDC marks line up: the mark on the crankshaft pulley is opposite the pointer on the front cover, and the camshaft mark is at the top.
- Check the valve lash on the No. 1 and No. 4 cylinders. Insert the feeler gauge between the camshaft lobe and the follower: intake 0.20-0.30 mm (nominal 0.25 mm), exhaust 0.30-0.40 mm (nominal 0.35 mm). The gauge should slide through with light resistance.
- If the lash is out of spec, loosen the adjusting screw locknut with a 12 mm wrench while holding the screw with a screwdriver or the special wrench. Turn the screw until the feeler gauge shows the correct lash, tighten the locknut to 12-15 N·m (9-11 lb-ft), and recheck the lash (the screw can shift as you tighten it).
- Turn the crankshaft 180° (half a turn). The camshaft mark now points left. Check and adjust the valves on the No. 2 and No. 3 cylinders the same way.
- Turn the crankshaft another 180°. The camshaft mark is now at the bottom. Check and adjust the remaining valves.
- Turn the crankshaft two full revolutions and recheck all the lash settings to make sure the adjustment has not changed.
- Wipe the mating surfaces of the cylinder head and the cover clean of oil. Install the cover with a new gasket (or the old one if it is intact), and tighten the bolts in a crisscross pattern to 8-10 N·m (6-7 lb-ft).
Common mistakes and warnings
- Incorrect lash leads to power loss and valvetrain damage: too little lash risks burned valves, and too much causes ticking and accelerated wear
- Work only on a cold engine, because hot measurements will give incorrect values
- If the lash is far from nominal or the screws do not have enough adjustment range, the followers need replacing or the camshaft lobes need to be checked for wear
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Mazda
It's hard to find anyone today who would dispute that cars from the Japanese company Mazda are among the most beautiful…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →