https://autopapyrus.com/catalog/mercedes-benz/e-class/guides/removing-and-installing-the-rear-seat/
Mercedes-Benz E-Class W124 (1st generation): Removing and Installing the Rear Seat
The rear bench of the W124 sedan consists of two parts: the lower cushion and the backrest. The cushion is held by retainers along its front edge. The backrest is secured at the bottom and top by hooks and retainers. The order is always the same: cushion first, then backrest. The exact number and location of the backrest fasteners can vary from car to car, so after removing the cushion, inspect the lower part of the backrest and proceed accordingly.
Parts
3| № | Part |
|---|---|
| 01 | Rear seat cushion assemblyif wornFind on Amazon → |
| 02 | Rear seat backrest assemblyif wornFind on Amazon → |
| 03 | Mounting clips and retainersif damagedFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
4Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 9 more.
See manuals →
Step by step
10 steps- Open both rear doors for unobstructed access. If the head restraints are removable, pull them upward while pressing the release latch at the base of the post.
- Locate the front retainers of the cushion. They are under the front edge, on the left and right, closer to the door sills.
- Grab the cushion at a front corner and pull sharply upward with the flat of your hand. Do not pry the latches with a screwdriver: the retainer housings will crack. If the cushion does not release, press the latch with the pry tool and try again.
- Lift the front edge and pull the cushion forward and up from under the backrest. If there is a connector underneath (for example, seat heating), disconnect it before removing the cushion completely.
- Inspect the base of the backrest. Remove the mounting bolts at the bottom with a 10 mm wrench (usually a 10 mm head; if yours is a different size, use the one that fits). Note which bolts came from where.
- Press on the backrest and slide it upward to free the upper hooks. Lift the backrest slightly and remove it. On cars with a folding backrest, note that it has a locking pin at the door-side edge: first make sure it is released.
- While the bench is out, inspect the access covers, wiring and the floor underneath for dust, moisture and signs of corrosion. This is a convenient time to clean and dry the area.
- Installation is the reverse of removal. First hang the backrest on its upper hooks, press it down until it locks, and tighten the lower bolts. No torque is specified for these bolts, so tighten them moderately, without jerking, until the washer seats.
- Route the seat belts through the slots so that the buckles do not end up under the cushion. Reconnect the connector if there was one.
- Insert the cushion with its rear edge under the backrest, then press down the front corners until the retainers click. Pull up on the cushion to confirm it is secure, and check that the seat belt buckles work properly.
Common mistakes and warnings
- Do not remove the backrest before the cushion: you can bend the frame brackets
- Do not pry the latches with a screwdriver
- If there are yellow airbag or belt pretensioner connectors in the cabin, do not disconnect them without disconnecting the battery and without experience
- Contact a repair shop if you are unsure
- The bolt tightening is approximate; check exact values against the manufacturer's specifications