https://autopapyrus.com/catalog/mitsubishi/canter/guides/glow-plug-and-glow-plug-relay-diagnosis/
Mitsubishi Canter 3.9 D 4D34 (1996): Glow Plug and Glow Plug Relay Diagnosis
If a cold 4D34 is hard to start, emits white smoke, and misfires until it warms up, the cause is often the glow plugs, the relay, or the control circuit. Diagnosis goes from simple to complex: first the power supply and relay, then the resistance of each glow plug. Check the manufacturer's service manual for the exact resistance and torque values for this engine.
Key figures
- Resistance of a good metal glow plugbelow 5 Ω. Measure it with a multimeter between the plug terminal and engine ground (step 8). An infinite reading means a broken filament.
- Resistance of a good ceramic glow plugbelow 1 Ω. This is the same measurement (step 8), if the vehicle has ceramic plugs.
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the glow plug relay is and how to test a plug
- 1Glow plug relay: a one-piece metal case with a dome on a bracket. With the ignition on, a working relay clicks when heating starts and clicks again when it stops.
- 2Relay power terminal: a stud with a nut on the base, the wire to the plugs is attached. Check the voltage on it with the ignition on.
- 3Wire harness: a thick corrugated harness from the bottom of the relay. Inspect the wires and the connector.
- 4Glow plug: put one multimeter probe on the terminal and the other on the engine ground. Infinite value means a broken heater, replace the plug.
Parts
2| № | Part |
|---|---|
| 01 | Glow plugs for 4D34 dieselset of 4 for 4 cylinders, 4 pcsFind on Amazon → |
| 02 | Glow plug relay (preheating relay) for 1996 Mitsubishi CanterFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
12 steps- Check the symptoms. If the glow indicator light on the dash does not come on at all, look for a problem with power, the fuse, the relay, or the switch. If the light comes on but the engine runs poorly when cold, some of the glow plugs are most likely burned out.
- Check the battery charge and the condition of the terminals. Glow plugs draw a lot of current, and if the voltage sags, preheating is weak. Clean and tighten the terminals.
- Find the fuse or fusible link for the glow plug circuit in the fuse box and in the engine compartment. Inspect them. If one has blown, do not install a higher-rated one. First find the cause (a short to ground, or a shorted glow plug).
- Find the glow plug relay (it is mounted in the engine compartment or behind the dash, closer to the firewall). Turn the ignition on without starting the engine. A good relay clicks when preheating starts and clicks a second time when preheating ends.
- If there is no click, use a multimeter to check for power and the control signal at the relay connector with the ignition on. If there is no control signal, look for a fault in the ignition switch, the preheat timer, or the wiring. If the signal is present but the relay stays silent, the relay is faulty.
- If the relay clicks, check the voltage at the relay's power output terminal to the glow plugs with the ignition on. If there is no voltage, the relay contacts are burned or the contact plate inside is cracked. This kind of relay usually cannot be taken apart, so it is replaced as a unit.
- Turn the ignition off and disconnect the negative battery terminal. Remove the power wire or bus bar from the glow plugs.
- Measure the resistance of each glow plug with a multimeter between its terminal and engine ground. An infinite reading means the filament is broken and the plug must be replaced. A good metal glow plug is considered to be one with resistance below 5 Ω, and a good ceramic one below 1 Ω. The exact specification for the 4D34 is in the manufacturer's service manual. All four plugs should also read close to each other, and a plug that differs noticeably is suspect.
- If you need to test a plug under load, briefly apply power to it through a fuse that matches the vehicle's electrical system. A good plug heats up to a red glow quickly (on a plug that has been removed) or draws noticeable current, while a dead one does not heat up. Do this only on a removed plug and only for a short time, to avoid overheating it.
- If a plug will not come out or breaks off, do not use excessive force. Warm up the engine, apply penetrating oil, and work the plug out with a turning motion, varying the force. A broken tip left in the cylinder head is a job for a repair shop.
- Replace the plugs as a set. Thread the new ones in by hand, then tighten them with a torque wrench to the torque in the manufacturer's service manual (glow plugs usually take a low torque, so do not tighten them all the way). Do not mix up the plug type or voltage.
- Connect the power wire and tighten the terminal nut carefully, without cross-threading it. Reconnect the battery. Turn the ignition on and make sure the glow indicator light comes on and goes out and the relay clicks. Then start the engine.
Common mistakes and warnings
- Always disconnect the negative battery terminal before removing wires from the glow plugs
- The glow plug power bus is fed directly from the battery, and shorting it with a wrench produces heavy sparks and can cause a fire
- Do not apply voltage above the rated value to the plugs, and do not leave them energized for long, because an overheated plug fails
- Do not use starting fluid on a diesel with glow plugs, because it can ignite and damage the engine