Autopapyrus · Mitsubishi L200 (Triton) 2.5 DI-D 4D56 (2012)
https://autopapyrus.com/catalog/mitsubishi/l200/guides/checking-and-adjusting-valve-clearances/
https://autopapyrus.com/catalog/mitsubishi/l200/guides/checking-and-adjusting-valve-clearances/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Mitsubishi L200 (Triton) 2.5 DI-D 4D56 (2012): Checking and Adjusting Valve Clearances
The 4D56 diesel has no hydraulic lash adjusters. The clearance between the rocker arm and the valve stem tip is set manually with a screw and locknut. Check it with the engine warm. The factory clearance for the 4D56 is 0.25 mm.
Parts
2| № | Part | Genuine part no. |
|---|---|---|
| 01 | 4D56 engine valve cover gasket (set with stud or bolt seals)Find on Amazon → | 1035A108 |
| 02 | Engine oilfor topping off if neededFind on Amazon → |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
8
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 3 more.
See manuals →
Step by step
11 steps- Warm the engine up to normal operating coolant temperature, about 80-90 °C, and shut it off. Let it cool until it is safe to touch, but do not let it get fully cold.
- Remove the air duct and hoses that block access to the valve cover. Disconnect the crankcase ventilation hose. Move aside the wiring harnesses and brackets that cover the valve cover, and mark their positions.
- Loosen the valve cover fasteners evenly in a crisscross pattern and remove the cover. Check the condition of the gasket and the fastener seals. If the rubber is hardened or torn, replace it.
- Fit a wrench on the crankshaft pulley bolt. Turn the crankshaft only in the direction of engine rotation, which is clockwise when viewed from the front. Check and adjust the clearances after the crankshaft has made one full turn or more.
- Bring the No. 1 cylinder piston to TDC on the compression stroke. In this position both valves of cylinder 1 are closed and the rocker arms move freely. Compare the mark on the pulley with the mark on the housing. If you are not sure where the compression stroke is, look at the rocker arms of cylinder 4: at that moment its valves are overlapping.
- Use a 0.25 mm feeler gauge to check the clearance between the rocker arm adjusting screw and the valve stem. The gauge should slide through with light resistance. Check the clearance on valves whose cam lobe is pointing away from the rocker arm, meaning the valve is fully closed.
- If the clearance is out of specification, loosen the locknut on the adjusting screw and turn the screw until the feeler gauge slides through with light drag. Hold the screw with a screwdriver and tighten the locknut. Then recheck the clearance, because it often changes as the nut is tightened.
- Mark the checked valves with chalk. Turn the crankshaft one full turn and repeat the check on the remaining valves. On a four-cylinder engine the valves are usually checked in pairs, following the firing order. Verify the firing order and the procedure diagram against the manufacturer's service manual.
- After adjusting, turn the crankshaft two full turns in the direction of rotation. Check all the clearances with the feeler gauge again and readjust if necessary.
- Clean the mating surfaces of the cylinder head and the cover of old sealant and oil. Install the gasket and the cover, and tighten the fasteners in a crisscross pattern, gradually, with light force. The tightening torque for the valve cover bolts and the adjusting screw locknuts is not given in the available materials, so check it against the manufacturer's service manual. Do not overtighten: the cover and gasket will deform.
- Reinstall the hoses, the ventilation hose and the wiring harnesses. Start the engine, check that it idles properly and that there are no oil leaks. Listen for ticking: a smooth, even valve tick is normal.
Common mistakes and warnings
- Do not turn the crankshaft against the direction of rotation: this can shift the timing belt and upset the valve timing
- Do not set the clearance smaller than specified: the valves will not seat fully on the warm engine and will burn
- If you lack experience, leave the job to a repair shop: a mistake in finding TDC leads to incorrect adjustment