← Pajero-montero

Mitsubishi Pajero (Montero) 3.0 V6 6G72 (2011): Intake Manifold Removal and Installation

The 6G72 manifold has two parts: the upper section (plenum with throttle body) and the lower section, which bolts to both cylinder heads and carries the fuel rail with injectors. This job is done when replacing gaskets, when coolant or oil leaks under the manifold, or to access the valve covers and spark plugs. The torque values below are approximate; verify the exact values against the manufacturer's specifications.

DifficultyHard Time4-6 hours Steps36

Parts

5
№PartAlternatives
01 Intake manifold gasket set (lower manifold-to-cylinder head gasket, upper section/plenum gasket, throttle body gasket)Find on Amazon → AlternativesFel-ProVictor ReinzAjusa
02 Fuel injector O-ringsFind on Amazon →
03 Coolant hosesif wornFind on Amazon →
04 Cooling system clampsif wornFind on Amazon →
05 Coolantfor topping offFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

10

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

36 steps · 7 stages
Stage 1 of 7 Preparation 5 steps
  1. Let the engine cool down completely. Working on a hot engine around coolant and fuel is dangerous.
  2. Disconnect the negative battery terminal. If the vehicle has a radio security code, write it down beforehand.
  3. Remove the plastic decorative engine cover, if installed.
  4. Relieve the fuel system pressure: pull the fuel pump relay or fuse, start the engine and let it stall, then crank it with the starter for 2-3 seconds. Keep rags near the fuel connections.
  5. Partially drain the coolant: the lower part of the manifold has coolant passages. Drain about 2-3 L (2.1-3.2 qt) through the radiator drain valve into a clean container if you plan to reuse the coolant.
Stage 2 of 7 Removing the surrounding components 6 steps
  1. Remove the air filter with its housing and the corrugated air duct leading to the throttle body. Disconnect the mass airflow sensor connector and the crankcase ventilation hose.
  2. Disconnect the throttle position sensor connector and the idle air control valve connector. Take photos of the position of all connectors and hoses.
  3. Disconnect the throttle cable (if equipped on your model) and remove the coolant hoses that heat the throttle body. Plug the hoses and place a container underneath.
  4. Disconnect the vacuum hoses from the plenum: to the brake booster, the charcoal canister valve, and the fuel pressure regulator. Label each hose with masking tape.
  5. Disconnect the connectors of the sensors located on the manifold: the manifold absolute pressure and intake air temperature sensor, and the EGR valve (if equipped). Release the wiring harnesses from their brackets.
  6. Remove the ignition coil wiring and the spark plug wires from their retainers if they are in the way, and mark their order.
Stage 3 of 7 Removing the upper manifold (plenum) 3 steps
  1. Remove the bolts and nuts securing the plenum to the lower manifold, and the bracket securing the plenum to the block. Loosen them in a crisscross pattern, gradually, working from the edges to the center.
  2. Remove the plenum together with the throttle body. If the throttle body needs to be removed separately, remove its 4 bolts and take it off with its gasket.
  3. Immediately cover the intake ports of the lower section with clean rags or plugs. Any bolt or piece of gasket that falls into a cylinder will cause severe engine damage.
Stage 4 of 7 Removing the lower manifold 6 steps
  1. Disconnect the fuel hoses from the rail (supply and return, if present), using a rag as a precaution, since residual pressure and fuel will leak out. Press the release tabs on the quick-connect fittings or unscrew the fittings.
  2. Disconnect the connectors of all injectors and release the harness from the brackets. The cylinder numbering is a reference for reassembly.
  3. Remove the fuel rail mounting bolts and pull the rail out together with the injectors, carefully and without tilting it. Alternatively, leave the rail with the injectors on the manifold and remove them as an assembly, if access allows.
  4. Disconnect the coolant hoses going to the lower manifold and any vacuum lines remaining on it.
  5. Remove the bolts securing the lower manifold to the cylinder heads, gradually, from the edges to the center, in several passes. Do not remove the manifold by brute force: if it is stuck, tap it gently with a rubber mallet through a wooden spacer.
  6. Lift the manifold, keeping it level, and remove it. Do not let coolant get into the cylinders.
Stage 5 of 7 Surface preparation 3 steps
  1. Clean the mating surfaces of the heads and the manifold of gasket residue with a plastic or brass scraper and a degreaser. Do not scratch the aluminum.
  2. Check the manifold's mating surface for warping with a straightedge, and inspect it for cracks and damaged threads.
  3. Replace the injector O-rings, lubricating them with clean engine oil before installation.
Stage 6 of 7 Installation 8 steps
  1. Place the new gaskets on the cylinder heads. Use only gaskets of the correct shape. Sealant is usually not needed on metal-rubber gaskets; for paper or rubber ones, follow the gasket manufacturer's recommendations.
  2. Set the lower manifold in place and make sure the gaskets have not shifted and the manifold is not cocked.
  3. Thread the lower manifold bolts in by hand, then tighten them with a torque wrench in several passes from the center to the edges. Approximate torque is 18-25 N·m (13-18 lb-ft) (verify the exact value against the manufacturer's specifications).
  4. Install the fuel rail with the injectors and tighten its bolts. Approximately 10-20 N·m (7-15 lb-ft) (verify the exact value against the manufacturer's specifications). Connect the injector connectors and the fuel hoses.
  5. Connect the coolant hoses, vacuum lines and harnesses on the lower manifold.
  6. Remove the plugs from the ports. Install the new plenum gasket and the plenum itself, and tighten its fasteners in a crisscross pattern in several passes. Approximate torque is 13-20 N·m (10-15 lb-ft) (verify the exact value against the manufacturer's specifications).
  7. Install the throttle body with a new gasket and tighten the bolts to approximately 10-20 N·m (7-15 lb-ft).
  8. Reconnect all connectors and vacuum hoses using your photos and labels, then the throttle cable, throttle body heater hoses, air duct, air filter housing and coil wiring.
Stage 7 of 7 Starting and checking 5 steps
  1. Reconnect the battery terminal. Top off the coolant to the proper level in the expansion tank.
  2. Install the fuel pump relay or fuse, turn the ignition on for 3-5 seconds (without starting) 2-3 times to build pressure, and inspect the connections for fuel leaks.
  3. Start the engine and let it warm up until the thermostat opens. Bleed the air from the cooling system: hold the engine at 2000-2500 rpm until the fan turns on, and top off the coolant if necessary.
  4. Check for vacuum leaks (unstable idle, hissing), coolant and fuel leaks, and OBD error codes. Clear the error codes after the check.
  5. After 1-2 days, check the coolant level on a cold engine and the tightness of the plenum fasteners.

Common mistakes and warnings

  • Working on the fuel system: gasoline vapors are flammable, so eliminate open flames and sparks and keep a fire extinguisher nearby
  • Coolant is toxic, so collect it and dispose of it properly
  • If you have no experience disassembling engines, leave the job to a repair shop: a mistake during assembly leads to vacuum leaks, fluid leaks or engine damage
Spotted a mistake? Tell us →