https://autopapyrus.com/catalog/nissan/ad/guides/rough-running-misfire-and-stalling/
Diagnosing Carburetor and Idle Problems: Rough Running (Misfire) and Stalling
A rough-running (misfiring) engine that stalls right after a fuel filter and distributor replacement is most often not caused by the carburetor itself. The usual culprits are swapped spark plug wires, a displaced ignition timing setting, a fuel filter installed backwards, or vacuum hoses that were misplaced. Rule out these causes first, then move on to carburetor cleaning and adjustment.
Parts
6| № | Part | Genuine part no. |
|---|---|---|
| 01 | In-line fuel filterFind on Amazon → | |
| 02 | Spark plugsFind on Amazon → | 22401-20J05 |
| 22401-20J06 | ||
| 22401-20J07 | ||
| 03 | High-tension (spark plug) wiresFind on Amazon → | |
| 04 | Carburetor gasket (insulator spacer)Find on Amazon → | 16174-53Y01 |
| 16455-51J00 | ||
| 05 | Vacuum hosesFind on Amazon → | |
| 06 | Carburetor rebuild kit for Nissan GA13if neededFind on Amazon → | 16009-51J00 |
| 16009-51J01 |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
9Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
13 steps- Check the wire order at the distributor and spark plugs. The firing order of the 4-cylinder GA13 is 1-3-4-2. Make sure the No. 1 cylinder wire is on the terminal that the rotor points to when the No. 1 piston is at TDC on the compression stroke. A single wire moved over by one position causes exactly this: rough running, popping and stalling.
- Check the distributor installation. Set the crankshaft pulley marks to TDC for cylinder No. 1 (compression stroke), make sure the rotor points to the No. 1 cylinder terminal, and make sure the distributor body is fully seated in its bore. If the distributor went in one tooth off on the drive gear, the ignition timing will be off, and the engine will run rough or will not hold an idle.
- Warm up the engine and set the ignition timing with a timing light. For idle, the base timing angle is given on the sticker under the hood (usually a few degrees BTDC). Disconnect and plug the vacuum advance hose while adjusting. Loosen the distributor clamp, rotate the distributor body until the timing mark lines up with the specification on the sticker, then tighten the clamp.
- Inspect the vacuum hoses of the distributor, carburetor and valves. When a distributor is replaced, the vacuum advance hose is often removed and then reconnected to the wrong port or is cracked. Make sure the hoses are intact, have no vacuum leaks, and are connected according to the diagram on the sticker under the hood.
- Check the fuel filter. The filter has a flow direction arrow: it must point from the fuel pump toward the carburetor. Make sure the clamps are tight and the hoses are not pinched and do not draw in air. If the filter is installed backwards, the engine stalls under load and at idle.
- Check the fuel supply. Disconnect the hose at the carburetor inlet, point it into a container and crank the engine with the starter: there should be a steady stream. A weak stream means a clog, a failing pump or a pinched hose. Also check the fuel level in the float bowl through the sight glass (if equipped) or by the level marks.
- Check the spark plugs: the gap is usually 0.8-1.0 mm (confirm against the sticker under the hood). Dark, fuel-soaked plugs should be cleaned or replaced. Inspect the wires: leakage to ground shows up as sparks in the dark. Check the distributor cap and rotor for cracks and carbon tracking.
- Check for air leaks at the carburetor gasket and the intake manifold. With the engine running, carefully spray carburetor cleaner on the joints: a change in engine speed shows where the leak is. Replace the gasket if the joint does not seal properly.
- Clean the carburetor. Remove the air filter, then use cleaner to flush the idle jets, the idle circuit passage, the throttle plate and the mixture limiter. Clogged idle jets are a typical cause of unstable idle and of stalling when you lift off the throttle.
- Check the idle cut-off (anti-dieseling) valve, which is the solenoid valve of the idle jet. It should click when you turn the ignition on. If it does not click, check the power supply at the connector; a faulty valve makes the engine stall at idle.
- Adjust the idle on a warm engine: use the throttle (idle speed) screw to set the speed, and use the mixture screw to get the smoothest running (on average about 700-900 rpm; use the exact value from the sticker under the hood). Adjust with all electrical loads off, with the engine oil warm and the choke fully open.
- Check the operation of the choke plate and the automatic choke: with a warm engine the choke plate must be fully open. If it sticks, the mixture is too rich, and the engine runs rough and stalls.
- If the engine still runs rough after all of this, check cylinder compression and the condition of the timing belt/chain, since incorrect valve timing after removing the distributor can cause the same symptoms. A difference of more than 1 bar (about 14.5 psi) between cylinders calls for separate diagnosis.
Common mistakes and warnings
- Work on the fuel system away from open flames and sparks, keep a fire extinguisher nearby and avoid fuel spills
- Do not run the engine in an enclosed space without ventilation
- If the ignition timing and wire order have been verified and the problem persists, take the car to a shop experienced with carbureted Japanese engines
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Nissan
Over the course of 80 years, this Japanese automaker has come a long way and risen to become a leader of the global…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →