https://autopapyrus.com/catalog/nissan/expert/guides/engine-management-system-diagnostics/
Nissan Expert 1.9 dCi 100 hp (2005): Engine Management System Diagnostics
Diagnostics comes down to reading fault codes and viewing live data, then checking the mechanical and electrical side of the suspect circuit. The exact procedure and component locations for this specific version are not documented in public service materials, so what follows is the general principle for common rail diesels. Check specific pressure and resistance values against the manufacturer's specifications.
Parts
9| № | Part |
|---|---|
| 01 | Fuel filterif faultyFind on Amazon → |
| 02 | Mass air flow sensorif faultyFind on Amazon → |
| 03 | Crankshaft position sensorif faultyFind on Amazon → |
| 04 | Rail pressure sensorif faultyFind on Amazon → |
| 05 | Coolant temperature sensorif faultyFind on Amazon → |
| 06 | Exhaust gas recirculation (EGR) valveif faultyFind on Amazon → |
| 07 | Glow plugsif faultyFind on Amazon → |
| 08 | Glow plug control relayif faultyFind on Amazon → |
| 09 | Injectorsif faultyFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
11 steps- Clarify the symptom: no start, misfire, smoke, lack of power, limp mode, or the Check Engine or glow plug light being on. Note the conditions in which it appears: cold or hot engine, under load or at idle.
- Do a quick inspection. Check the oil and coolant level and condition, air filter cleanliness, the integrity of the turbo and intercooler hoses (boost leaks and air intake leaks), any fuel leaks, the condition of connectors and wiring harnesses on the engine, and the battery terminals and ground connections.
- Check the battery and charging. Battery voltage with no load should be about 12.4-12.7 V, and with the engine running about 13.8-14.5 V. A drop below roughly 9.5 V during cranking causes false fault codes and starting problems.
- Connect the scanner to the OBD diagnostic port under the dashboard on the driver's side. Turn the ignition on and read the codes from the engine control unit. Write down all codes, including stored and pending ones, and only then clear them.
- View the freeze frame data and live data with the engine warm. Evaluate coolant temperature, mass air flow at idle (compare it with the expected value for a 1.9 L engine at that rpm), boost pressure, actual and target rail pressure, pedal position, rpm, injector corrections, and battery voltage.
- Check the suspect circuit according to the code. Disconnect the sensor connector, inspect the contacts for corrosion, and test the wires for open circuits and shorts to ground and to power. Confirm that the reference voltage (usually about 5 V) is present at the sensor. Compare the sensor resistance with the specified value for that sensor.
- If the fault relates to fuel pressure or there are starting problems, check the low-pressure side of the fuel system: the supply pump, a clogged fuel filter, air leaks (bubbles in a clear return or supply hose), and a clogged strainer in the tank. Only after that move on to the high-pressure side.
- If the fault relates to air or smoke, check the EGR valve (sticking, carbon buildup), the throttle body if fitted, the tightness of the boost air path, the control vacuum or the turbo electrics, and the air flow meter. Temporarily disconnecting the air flow meter is acceptable only as a diagnostic technique, not as a repair.
- If the fault relates to the glow plugs, measure the current or resistance of each plug and check the preheat relay or control unit and its power supply.
- For a misfire on multiple cylinders, check the per-cylinder fuel delivery corrections on the scanner and the injector return flow (leak-off test). This requires measuring containers and a set of blanking caps. If you lack experience, it is better to leave this to a specialist.
- After fixing the cause, clear the codes, warm up the engine, and take a 10-15 minute test drive under varied loads. Read the codes again and make sure they have not returned.
Common mistakes and warnings
- Do not disconnect the high-pressure fuel lines or loosen the rail and injector fittings on a running or just-stopped engine: pressure remains in the system, and a jet of pressurized diesel fuel is dangerous
- Work on the high-pressure line only with the engine cold and keep everything clean, because any dirt will ruin the injectors
- Coding new injectors, relearning the control unit, and coding require a special scanner or equipment
- If you don't have such equipment and the fault involves the control unit or the immobilizer, go to a specialist repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Nissan
Over the course of 80 years, this Japanese automaker has come a long way and risen to become a leader of the global…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →