Autopapyrus · Nissan Largo (1995)
https://autopapyrus.com/catalog/nissan/largo/guides/cooling-system-bleeding-and-removing-air-from-the-heater-circuit/
https://autopapyrus.com/catalog/nissan/largo/guides/cooling-system-bleeding-and-removing-air-from-the-heater-circuit/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Nissan Largo (1995): Heater System Bleeding and Removing Air from the Cooling System
An air pocket in the cooling system causes a cold heater, gurgling behind the dash, overheating and temperature gauge swings. Air is removed by filling the coolant slowly with the heater set to maximum heat, the bleed screws open, and the engine warmed up until the thermostat opens. The bleed screw locations depend on the engine, so inspect the engine bay first.
Key figures
- Coolant filling ratefilling faster introduces bubbles into the coolant (step 7)no more than 2 liters (2.1 qt) per minute
- Temperature for checking the levelthe radiator cap can be opened safely at this point (steps 15-16)about 50 °C (122 °F)
- Engine speed for bleeding the heaterthis pushes air out of the heater core (step 13)1000 rpm for about 30 seconds, then smoothly up to 3000
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
2| № | Part |
|---|---|
| 01 | Coolant (antifreeze)for topping offFind on Amazon → |
| 02 | Copper sealing washers for bleed screwsif fitted to the engineFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6Step by step
20 steps · 4 stagesStage 1 of 4 Preparation 5 steps
- Park the vehicle on level ground, shut off the engine and let it cool down completely. Never remove the radiator cap on a hot engine: pressurized coolant causes burns.
- Open the hood and locate the radiator, the expansion tank, the thermostat and the hoses running to the heater. Look for the bleed screws (fittings) on the thermostat housing, on the intake manifold or water outlet, and on the heater pipe. On versions with a rear heater, there is a screw at the bottom of the rear heater.
- Check the level in the tank and the condition of the hose clamps and hoses. Fix any leaks or wet hoses before bleeding.
- To help the air escape, you can raise the front of the vehicle on a jack and jack stands. The heater and the high points of the system will then sit higher than the radiator, and the air will travel toward the filler neck.
- In the cabin, set the temperature control to maximum heat so the heater valve or blend door is open. Do not start the engine yet.
Stage 2 of 4 Filling and air removal 5 steps
- Remove the radiator cap and open the bleed screws on the engine and on the heater pipe. Turn them out 1-2 turns; do not remove them completely.
- Install the funnel and pour coolant into the radiator slowly, no faster than 2 L (2.1 qt) per minute. Filling too fast introduces bubbles into the coolant.
- When coolant without bubbles starts to flow from a bleed screw opening, tighten that screw. The tightening torque is small, about 6-8 N·m (4-6 lb-ft); check the exact value in the manufacturer's specifications. If there is a copper washer, replace it with a new one.
- Repeat for each bleed screw in turn. Top off the coolant to the rim of the radiator filler neck.
- Fill the expansion tank to the MAX mark and install the radiator cap.
Stage 3 of 4 Warm-up and bleeding 5 steps
- Make sure the heater control is still set to maximum heat, then start the engine.
- Hold the engine at an elevated speed of about 2000-3000 rpm until it warms up and the thermostat opens. A sign that it has opened: the lower radiator hose becomes hot. Watch the temperature gauge and do not allow the engine to overheat.
- To push air out of the heater core, rev the engine several times: 1000 rpm for about 30 seconds, then smoothly up to 3000 rpm. Repeat three times.
- While the engine is warm, move the temperature control through different positions between hot and cold. Listen for the sound of coolant flowing behind the dash. If you hear gurgling, there is still air in the system; repeat step 13.
- Shut off the engine and let it cool to about 50 °C (122 °F).
Stage 4 of 4 Topping off and checking 5 steps
- Carefully remove the radiator cap and check the level. It usually drops because the air has escaped. Top off to the filler neck.
- If the level has dropped a lot, repeat steps 11-16. Consider the bleeding complete when the level stops dropping.
- Install the radiator cap and fill the expansion tank to MAX.
- Take a test drive of 10-15 minutes. The heater should get hot quickly, and both heater hoses should feel hot to the touch.
- Let the engine cool down and check the level in the expansion tank and in the radiator once more. Top off if necessary.
Common mistakes and warnings
- Do not open the radiator cap or the bleed screws on a hot engine; this can cause burns
- Do not mix different types of coolant
- If the heater is still cold after bleeding and the level keeps dropping or the engine overheats, the cause may be a faulty thermostat, a clogged heater core or a head gasket
- In that case, have it diagnosed at a repair shop
- The same procedure also applies when replacing the coolant
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Nissan
Over the course of 80 years, this Japanese automaker has come a long way and risen to become a leader of the global…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →