Autopapyrus · Nissan Micra (K12, 3rd generation)
https://autopapyrus.com/catalog/nissan/micra/guides/outer-tie-rod-end-replacement/
https://autopapyrus.com/catalog/nissan/micra/guides/outer-tie-rod-end-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Nissan Micra (K12, 3rd generation): Outer Tie Rod End Replacement
The tie rod end connects the tie rod to the steering knuckle. If it has play or the boot is torn, you will hear knocking while driving and the car will not hold its course well. A wheel alignment is required after replacement. Check the exact torque specifications against the manufacturer's service manual: the values below are working ranges.
Parts
3| № | Part | Genuine part no. |
|---|---|---|
| 01 | Outer tie rod end, Nissan Micra K12left or rightFind on Amazon → | 48520-AX600 |
| 48640-AX600 | ||
| 02 | Tie rod end bootif damagedFind on Amazon → | |
| 03 | Cotter pin or self-locking stud nutnewFind on Amazon → |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
9- Jack and jack stands Amazon →
- lug wrench Amazon →
- 17 mm and 19 mm wrenches and sockets for the ball stud nut Amazon →
- a second open-end wrench for the locknut Amazon →
- ball joint separator (or a hammer and a backing support) Amazon →
- wire brush Amazon →
- penetrating oil Amazon →
- torque wrench Amazon →
- marker or paint Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 7 more.
See manuals →
Step by step
13 steps- Park the car on level ground, apply the parking brake, and put a manual transmission in first gear. Loosen the lug nuts on the side you are working on, raise the front of the car, set a jack stand in place, and remove the wheel.
- Clean the tie rod threads and the locknut with a wire brush and apply penetrating oil. Let it soak for 10-15 minutes.
- Use a marker to mark the tie rod next to the locknut, or measure how many threads stick out past the locknut. This lets you restore roughly the same toe setting after replacement.
- If there is a cotter pin on the tie rod end stud, remove it. Unscrew the stud nut from the steering knuckle. If the stud spins, hold it with a hex key.
- Pop the stud out of the knuckle with a ball joint separator. Do not hit the knuckle itself with a hammer. If you use impact, first thread the nut on flush with the end of the stud threads so you don't damage them.
- Hold the tie rod with an open-end wrench on its flats, if it has them, and loosen the tie rod end locknut by half a turn to one turn.
- Unscrew the tie rod end from the tie rod, counting the turns. Compare the new part with the old one for length and side.
- Run the locknut along the tie rod and make sure the threads are clean and undamaged. Thread the new tie rod end on by the same number of turns, until it lines up with your mark.
- Insert the tapered stud into the knuckle. Check that the boot is intact and not twisted. Tighten the stud nut with a torque wrench to roughly 30-45 N·m (22-33 lb-ft); verify the exact value against the service manual. If needed, tighten the nut slightly further until the slot lines up with the cotter pin hole, then install a new cotter pin.
- Tighten the tie rod end locknut while holding the tie rod end so it can't rotate. Approximate torque: 30-50 N·m (22-37 lb-ft). Make sure the boot doesn't get twisted.
- Install the wheel, lower the car, and tighten the lug nuts in a crisscross pattern. The typical torque for this model is about 100-120 N·m (74-89 lb-ft); confirm it in the service manual.
- With the car standing still, turn the steering wheel from side to side and check for play, knocking, or binding. Then take a test drive at low speed and check the tightness again.
- Be sure to get a wheel alignment (toe and camber) soon. The marks on the threads give only a rough setting, and without an alignment the tires will wear unevenly and the steering wheel may sit off-center.
Common mistakes and warnings
- Steering is a safety-critical system
- If you don't have experience, leave the job to a repair shop
- A loose stud nut or locknut can lead to loss of steering control
- It is recommended to replace tie rod ends in pairs on the same axle if the other side is also worn
- If the steering wheel sits crooked after replacement or the car pulls to one side, don't put off the toe adjustment
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Nissan
Over the course of 80 years, this Japanese automaker has come a long way and risen to become a leader of the global…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →