Autopapyrus · Nissan Terrano 2.0 F4R (2018)
https://autopapyrus.com/catalog/nissan/terrano/guides/accessory-drive-belt-replacement/
https://autopapyrus.com/catalog/nissan/terrano/guides/accessory-drive-belt-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Nissan Terrano 2.0 F4R (2018): Serpentine Belt Replacement
One belt drives the alternator, the power steering pump and the A/C compressor. Maintenance schedule: replace every 60,000 km or 4 years, whichever comes first, regardless of condition. The tensioner is automatic and spring-loaded: the belt can be removed without removing the tensioner itself. Versions without A/C have a different routing and a different belt: compare the marking on the old belt with the new one.
Key figures
- Belt replacement intervalevery 60,000 km or 4 years, whichever comes first, even if the belt looks intact (introduction)
- New belt size7 ribs, length 1792 mm (7PK1792); use this marking to choose the belt for the A/C version (parts list)
- Tensioner wrench16 mm; it turns the pulley clockwise to release belt tension (steps 8-10)
- Socket for turning the engine18 mm; turn the crankshaft by the pulley bolt to inspect the entire belt (step 6)
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | V-ribbed accessory drive belt 7PK1792, 7 ribs, length 1792 mm (A/C version)Find on Amazon → | AlternativesGatesDaycoContitechBosch |
| 02 | Accessory drive belt tensioner with pulleyif wornFind on Amazon → | |
| 03 | Accessory drive belt idler (guide) pulleyif wornFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8- Pit or lift (or a jack and jack stands) Amazon →
- lug wrench Amazon →
- 16 mm wrench (box-end or socket with a handle) for the tensioner Amazon →
- 18 mm socket with a ratchet (to turn the crankshaft) Amazon →
- 13 mm socket and a Torx T40 bit (if replacing pulleys) Amazon →
- screwdriver or nut driver for the fender liner screws Amazon →
- flashlight Amazon →
- chalk or marker Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
23 steps · 6 stagesStage 1 of 6 Preparation and access 5 steps
- Shut off the engine and let it cool down. Place the vehicle over a pit or on a lift and set the parking brake.
- If you are working with a jack: loosen the lug nuts on the right front wheel, raise the vehicle, support it on jack stands and remove the wheel.
- Remove the right section of the engine splash guard (if installed).
- Remove the screws that hold the right fender liner to the bumper (about 3) and to the fender (about 1), and pull the front part of the liner back to expose the accessory drive.
- Take a photo or sketch the belt routing diagram: the belt runs around the crankshaft pulley, the tensioner pulley, the power steering pump pulley, the alternator pulley, the idler pulley and the A/C compressor pulley.
Stage 2 of 6 Inspecting the old belt and pulleys 2 steps
- Using the 18 mm socket on the crankshaft pulley bolt, turn the engine clockwise and inspect the belt along its entire length: cracks, separation, fraying, oil.
- Mark the position of the tensioner with chalk to judge how it is working.
Stage 3 of 6 Removing the belt 4 steps
- Fit the 16 mm wrench onto the hex of the tensioner.
- Rotate the pulley arm clockwise against the spring to release the belt tension.
- While holding the tensioner, slip the belt off one of the pulleys (easiest from the alternator or an idler pulley), then slowly release the tensioner.
- Remove the belt downward through the engine compartment.
Stage 4 of 6 Checking the pulleys 3 steps
- Spin each pulley by its inner bearing race. It should rotate smoothly and quietly, with no binding or play.
- If a pulley is noisy, binds or has play, replace it. The idler pulley is held by a bolt with a 13 mm head, the tensioner pulley by a Torx T40 screw, and the tensioner itself by a bolt with a 16 mm head. Tighten the fasteners with moderate force (approximately 20-45 N·m (15-33 lb-ft) depending on the bolt; for exact values, see the manufacturer's specifications). When installing the tensioner, the tab on its base must engage the slot in the accessory bracket.
- Wipe the pulleys clean of oil and dirt, and check the grooves for wear and built-up rubber.
Stage 5 of 6 Installing the new belt 4 steps
- Compare the new belt with the old one: 7 ribs, length 1792 mm, same profile.
- Install the belt on all pulleys except one (it is most convenient to leave an idler pulley or the alternator for last), strictly following the routing diagram: under the tensioner and idler pulleys.
- Use the 16 mm wrench to rotate the tensioner clockwise, slip the belt onto the last pulley and slowly release the tensioner.
- Make sure all 7 ribs of the belt are seated exactly in the grooves of each pulley, with no misalignment and without riding off the edge.
Stage 6 of 6 Reassembly and check 5 steps
- Turn the crankshaft 2-3 revolutions clockwise with the 18 mm socket and check the belt seating on the pulleys again.
- Reinstall the fender liner (screws) and the engine splash guard.
- Install the wheel and tighten the lug nuts in a crisscross pattern: approximately 100-110 N·m (74-81 lb-ft) (exact value per the specifications); after lowering the vehicle to the ground, tighten them fully.
- Start the engine, turn on the A/C, turn the steering wheel to full lock in both directions and listen: there should be no squealing, chirping or wobble. The battery warning light on the instrument panel should go out.
- After 50-100 km of driving, inspect the belt again and make sure it is not shifting.
Common mistakes and warnings
- Do not put your hands or tools between the belt and the pulleys while the engine is running
- Remove and install the belt only with the engine off, and operate the wrench on the tensioner smoothly: the spring is strong, and a slipping wrench can injure your hand
- Do not use the starter to turn the crankshaft, and do not turn the engine counterclockwise
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Nissan
Over the course of 80 years, this Japanese automaker has come a long way and risen to become a leader of the global…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →