← Vanette

Nissan Vanette F8 (1999): Intake Manifold Removal, Cleaning and Gasket Replacement

The F8 engine (1.8 L, SOHC) in the Vanette is a Mazda engine. The intake manifold comes off together with the throttle body or carburetor. It is most often removed because of vacuum leaks, an unstable idle or dirty intake passages. The exact procedure for this model is not documented in publicly available service materials. The general order of work and principles are given below, and you should check the tightening torques against the manufacturer's specifications.

DifficultyMedium Time3-5 hours Steps21

Parts

5
№PartGenuine part no.
01 Intake manifold gasket set, F8 engine (1.8 L)Find on Amazon → 10101-8C626
10101-9C625
A0101-8C586
02 Throttle body gasket (carburetor gasket)if removedFind on Amazon → 16175-57Y00
16175-96J00
16175-9C600
03 Fuel injector O-ringsfuel-injected enginesFind on Amazon →
04 Coolant (antifreeze)if drainedFind on Amazon →
05 Valve cover gasketas neededFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

10

Step by step

21 steps
  1. Work on a cold engine. Disconnect the negative battery terminal. Have bags and a marker ready: label all hoses and connectors before removing them.
  2. For access on the cargo Vanette, raise or remove the engine cover inside the cabin (under the driver and passenger seats, depending on the body type). Make sure the cover does not interfere with removing the manifold.
  3. Drain the coolant to a level below the manifold, or completely if the manifold has heater coolant hoses. Collect the coolant in a clean container.
  4. Remove the air filter, the air duct and the flexible hose connecting the air filter housing to the throttle body or carburetor. If there is an airflow meter, disconnect its connector.
  5. Disconnect the accelerator cable and, if equipped, the automatic transmission cable. Remove the cable bracket.
  6. Disconnect all vacuum hoses: brake booster, crankcase ventilation, EGR valves and solenoid valves. Label each hose.
  7. Disconnect the electrical connectors: throttle position sensor, idle speed control valve, fuel injectors, coolant temperature sensor. On a fuel-injected engine, relieve the pressure in the fuel rail and only then remove the fuel hoses. There must be no open flames nearby. On a carbureted engine, shut off the fuel supply, remove the hoses and plug them.
  8. Disconnect the coolant hoses that heat the throttle body or manifold. Leftover coolant will run out, so place a pan underneath.
  9. Remove the fuel rail with the injectors (on fuel-injected engines) and set it aside in a clean place.
  10. Loosen the nuts or bolts that hold the manifold to the cylinder head. Loosen them in a crisscross pattern from the edges toward the center, in two or three passes, so the manifold does not warp. Remove the brackets that support the manifold on the block.
  11. Carefully remove the manifold. If it is stuck, free it by tapping the sides lightly with a rubber mallet. Do not pry at the mating surfaces with a screwdriver.
  12. Cover the intake ports in the cylinder head with clean rags so that dirt and gasket remnants do not fall into the cylinders.
  13. Remove the remains of the old gasket from the cylinder head and the manifold with a plastic or brass scraper. Do not scratch the metal. The surfaces must be clean and dry.
  14. Clean the manifold with cleaner and blow out the passages with compressed air. Remove carbon and oil deposits (especially on the crankcase ventilation side) with a brush and rags. Make sure the passages are clear and the plugs and fittings are intact. Check the manifold mating surface with a straightedge. If the manifold is warped, replace it.
  15. Clean the throttle plate and the idle air passage. If there is heavy dirt inside the throttle body, clean it separately. Do not soak the electrical parts.
  16. Remove the rags from the ports. Install new gaskets without sealant unless the manufacturer requires otherwise. The gasket must lie flat, and its holes must line up with the ports.
  17. Install the manifold and tighten the fasteners from the center toward the edges, in two or three passes. Tighten to the manufacturer's torque specification. As a rough guide, for studs and nuts of this type it is about 15-25 N·m (11-18 lb-ft), but check the exact value in the service manual for the F8 engine. Do not overtighten, or you may strip the threads or damage the manifold surface.
  18. Install the injectors with new O-rings, lubricating the O-rings with clean engine oil. Reconnect the fuel rail, fuel hoses, coolant hoses, vacuum hoses and connectors according to your labels.
  19. Install the cables, air duct and air filter. Refill the coolant if you drained it, and bleed the cooling system of air pockets.
  20. Reconnect the battery. On a fuel-injected engine, turn the ignition on for a few seconds and check the fuel system for leaks. Start the engine and let it warm up. Check for vacuum leaks: inspect the joints of the manifold and hoses (for example, by spraying a short burst of carburetor cleaner while the engine is running; if the engine speed changes, there is a leak). Check the coolant level.
  21. After a test drive of 50-100 km, check the coolant level and the tightness of the manifold fasteners.

Common mistakes and warnings

  • Do fuel system work away from open flames and sparks, and do not smoke
  • Relieve the pressure in the fuel rail before disconnecting hoses
  • Coolant is toxic, so do not leave it in open containers
  • Do not let debris or gasket remnants get into the cylinders
  • Check the exact tightening torques and the hose routing against the manufacturer's specifications
  • If you have no experience working on fuel systems, leave the job to a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →