← Insignia Opel Insignia repair manuals →

Opel Insignia 2.0 Turbo A20NHT (2009): Mass Air Flow (MAF) Sensor Replacement

The mass air flow sensor is located in the intake tract between the air filter and the throttle body, near the air filter housing. Replacing it does not require any engine disassembly. Before replacing it, check whether simple cleaning helps and rule out air leaks in the intake.

DifficultyEasy Time15-30 minutes Steps8

Diagram: where the mass air flow sensor is and how to remove it

View from above with the hood openECOTECengine coverto the throttlePull the plug, not the wires2Connector with latch1Mass air flow sensor5Corrugated hose3Two sensor screws4Band clamp6Air filter housingTap to enlarge
  1. 1Mass air flow sensor: sits on the outlet pipe of the air filter housing. Unscrew it and replace it with a new or cleaned one, with its sealing ring.
  2. 2Electrical connector with a latch: press the latch, push it aside and remove the plug by pulling the plug itself, not the wires.
  3. 3Two sensor mounting screws: undo them carefully so you do not damage the plastic. When refitting, tighten moderately, without force.
  4. 4Band clamp at the joint of the pipe and the hose: loosen it if the sensor is built into the hose. Put it back after installation.
  5. 5Corrugated hose to the throttle: remove it if needed, and after assembly check that the air path is sealed.
  6. 6Air filter housing: a landmark. The sensor sits at its outlet, on the way of the air to the throttle body.

Part

№PartAlternatives
01 Mass air flow (MAF) sensor for Opel Insignia 2.0 Turbo A20NHTFind on Amazon → AlternativesBoschHellaSiemens/VDODelphi

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

4

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 4 more. See manuals →

Step by step

8 steps
  1. Make sure the engine is off and cool and the key is removed. For peace of mind, you can disconnect the negative battery terminal, but note that this will reset the clock and the radio settings.
  2. Locate the sensor: it is installed in the intake tract or in the air filter housing, at the filter outlet. An electrical connector plugs into it.
  3. Press the connector lock, release it and disconnect the plug. Pull on the plug, not on the wires.
  4. Remove the sensor: it is secured with two screws or a retaining clip. If the sensor is built into a duct or the housing cover, remove that part by loosening the clamp or unclipping the retainers. Undo the fasteners carefully so you don't damage the plastic.
  5. Inspect the sensor and the duct. If you only need to clean it, spray the sensing element with MAF sensor cleaner in short bursts (about ten), without touching it with your hands or wiping it with anything. Do not use alcohol or other liquids: they will ruin the sensor. Let it dry.
  6. Install the new or cleaned sensor, with its seal ring, in place. Tighten the screws lightly, without force: the housing is plastic. Use the torque specified by the manufacturer.
  7. Plug in the connector until it clicks, then reinstall the duct and the clamp or housing cover. Check that the air intake tract is airtight: an air leak after the sensor causes the same symptoms as a faulty sensor.
  8. Reconnect the battery terminal, start the engine and check that the idle is stable. Clear the fault codes with a scanner (typical codes: P0101, P0102) and take a test drive.

Common mistakes and warnings

  • Do not clean the sensor with alcohol, do not scrape or touch the sensing element, and do not damage the connector contacts. Similar symptoms (hesitation, unstable idle, increased fuel consumption, Check Engine light on) can also be caused by an air leak in the intake between the sensor and the turbocharger, or by worn spark plugs and ignition coils, so check the ducts and the air filter before buying a new sensor. The exact screw sizes and torque specifications for this model are not confirmed, so check them against the manufacturer's specifications.
Spotted a mistake? Tell us →